- All Journals
- Al-Qadisiyah University
- Basrah University
- Kirkuk University
- Mosul University
- The Iraqi Borad for Medical Specialization
- University of Anbar
- University of Technology
- Al Mustafa University
- Al-Zahraa University for Women
- Alnoor University
- Kunooz University
- Misan University
- Ninevah University
- Tikrit University
- University of Al-Hamdaniya
- University of Kerbala
Redrawing Operation a Star Shape from Cylindrical Shape Using Experimental and FE Analysis | ||
| Engineering and Technology Journal | ||
| Article 4, Volume 38, 1A, 2020, Pages 26-33 PDF (1.01 M) | ||
| DOI: 10.30684/etj.v38i1A.191 | ||
| Authors | ||
| Waleed Kh. Jawad1; Ali T. Ikal* 2 | ||
| 1Production and Metallurgy Engineering Department, University of Technology, Baghdad, Iraq | ||
| 2Production and Metallurgy Engineering Department, University of Technology, Baghdad, Iraq. | ||
| Abstract | ||
| The aim of this paper is to design and fabricate a star die and a cylindrical die to produce a star shape by redrawing the cylindrical shape and comparing it to the conventional method of producing a star cup drawn from the circular blank sheet using experimental (EXP) and finite element simulation (FES). The redrawing and drawing process was done to produce a star cup with the dimension of (41.5 × 34.69mm), and (30 mm). The finite element model is performed via mechanical APDL ANSYS18.0 to modulate the redrawing and drawing operation. The results of finite element analysis were compared with the experimental results and it is found that the maximum punch force (39.12KN) recorded with the production of a star shape drawn from the circular blank sheet when comparing the punch force (32.33 KN) recorded when redrawing the cylindrical shape into a star shape. This is due to the exposure of the cup produced drawn from the blank to the highest tensile stress. The highest value of the effective stress (709MPa) and effective strain (0.751) recorded with the star shape drawn from a circular blank sheet. The maximum value of lamination (8.707%) is recorded at the cup curling (the concave area) with the first method compared to the maximum value of lamination (5.822%) recorded at the cup curling (the concave area) with the second method because of this exposure to the highest concentration of stresses. The best distribution of thickness, strains, and stresses when producing a star shape by redrawing the cylindrical shape into a star shape. | ||
| Keywords | ||
| Redrawing operation of the star shape; stress and strain distribution | ||
| References | ||
|
[1] R. Narayanasamy and C. Loganathan, “The Influence of friction on the prediction of wrinkling of prestrained blanks when drawing through a conical die,” Materials and Design, Vol.28, pp. 904–912, 2007.
[2] D. H. Park, S .S. Kang and S .P. Park, “A study on improvement of formability for elliptical deep drawing process,” Journal of Materials Processing Technology, Vol.133, pp. 662 – 665, 2001.
[3] L. M. A. Hezam, M. A. Hassan, M. Hassab-Allah, and M. G. El-Sebaie, “Development of a new process for producing deep square cups through conical dies,” International Journal of Machine Tools & Manufacture, Vol.49, pp. 773–780, 2009.
[4] M. A. Hassan and D. Jafarlou, “A developed process for increasing deep drawability of rectangular metal cups with extreme aspect ratio: finite element simulation,” International Journal of Mechanical and Materials Engineering, Vol.8, No. 2, pp. 79-93, 2013.
[5] H. S. Lin and J. M. He, “Elliptical redrawing from circular and elliptical cups,” 11th International Conference on Technology of Plasticity, Vol.34, No. 7, pp. 899 – 904, 2014.
[6] A. Fazli and B. Arezoo, "An analytical method for prediction of limiting drawing ratio for redrawing stages of axisymmetric deep drawn components,” Journal of Archives Metallurgy and Materials, Vol.58, Issue.2, pp.264-270, 2014.
[7] K. A. Mahida and J. R. Shah, “Compare the FEA analysis of elliptic cups using simple die and conical die,” International Journal of Engineering Research & Technology, Vol. 4, pp. 462-467, 2015.
[8] W. K. Jawed and S. S. Dawood, “Drawing of hexagonal shapes from cylindrical cups,” Eng. & Tech. Journal, Vol.34, No. 6, pp. 1235-1246, 2016.
[9] C. P. Singh and C. Agnihotri, “Formability analysis at different friction conditions in axis-symmetric deep drawing process,” 5th International Conference of Materials Processing and Characterization, Vol. 4, pp. 2411–2418, 2017.
[10] A. H. Singal, “Experimental investigation of die geometry in multi-reverse drawing in one pass,” Ph.D., thesis, University of Technology, Iraq, 2019. | ||
|
Statistics Article View: 367 PDF Download: 280 |
||