- All Journals
- Al-Qadisiyah University
- Basrah University
- Kirkuk University
- Mosul University
- The Iraqi Borad for Medical Specialization
- University of Anbar
- University of Technology
- Al Mustafa University
- Al-Zahraa University for Women
- Alnoor University
- Kunooz University
- Misan University
- Ninevah University
- Tikrit University
- University of Al-Hamdaniya
- University of Kerbala
The Behavior of Piles Installed in Medium Dense Sand Within MSE Wall System | ||
| Engineering and Technology Journal | ||
| Article 5, Volume 39, Issue 8, 2021, Pages 1249-1256 PDF (859.12 K) | ||
| Document Type: Research Paper | ||
| DOI: 10.30684/etj.v39i8.1848 | ||
| Authors | ||
| Salah M. Hamza* ; Shaymaa T. Kadhim; Saad F. A. Al-Wakel | ||
| Civil Engineering Department, University of Technology, Baghdad, Iraq. | ||
| Abstract | ||
| Mechanically Stabilized Earth Walls (MSE) were widely used in several essential infrastructures, such as the abutments on a bridge. The need for a support base of a shallow or a deep bridge increased in the MSE wall system. In this research, factors affecting the performance of laterally loaded piles embedded in medium dense sand with a relative density of 50% behind an MSE wall were studied using lower-scale models in the laboratory. For instance, the effect of pile offset and the slenderness ratio on the pile's lateral capacity and pressure on the MSE wall. Three different slenderness ratios were introduced (i.e. L/D of 19.3, 21.7, and 24.1). The results showed a significant increase in pile lateral capacity occurring with the increase in pile offset or slenderness ratio (i.e., L/D). While increasing the pile offset reduced, the pressure on the wall so that the wall's effect will be insignificant when the pile offset reaches a value of 6D. | ||
Highlights | ||
| ||
| Keywords | ||
| Lateral Load; MSE wall (retaining wall); pile; BRC reinforcement; Medium dense sand | ||
| References | ||
|
[1] R. E. Hamdi, M. Y. Fattah and M. F. Aswad, “Studying the settlement of backfill sandy soil behind retaining wall under dynamic loads,” Engineering and Technology Journal, Vol. 38,Part A, No. 7, pp. 992-1000, 2020. [2] V. Elias, B. R. Christopher, and R. R. Berg, "Mechanically stabilized earth walls and reinforced soil slopes design and construction guidelines," FHWA, Washington D.C., ReportFHWA-NHI-00-043,2001. [3] W. K. Mohammed,” Factors influencing performance of a laterally loaded pile within an MSE wall system,” M.Sc. thesis, CEAE, University of Kansas, Lawrence, USA, 2016. [4] R.R. Berg, B.R. Christopher, and N.C. Samtani, “Design of mechanically stabilized earth walls and reinforced soil slopes,” FHWA, Washington D.C., Report FHWA-NHI-10-024, 2009. [5] M. C. Pierson, R.L. Parsons, J. Han, D.A. Brown, and W.R. Thompson, “Capacity of laterally loaded shafts constructed behind the face of a mechanically stabilized earth block wall,” Kansas Department of Transportation, Lawrence, Kansas,Report K-TRAN: KU-07-6, 2009. [6] K.R. Nelson, “Lateral resistance of piles near vertical MSE abutment walls at Provo Center Street,” M.Sc. thesis, Department of Civil and Environmental Engineering, Brigham Young University, Provo, UT, USA, 2013. [7] J. Han, “Lateral resistance of piles near 15 foot vertical MSE abutment walls reinforced with ribbed steel strips,”M.Sc. thesis, Department of Civil and Environmental Engineering, Brigham Young University,Provo, UT, USA,2014. [8] K. Rollins, J. Price, and J. Bischoff, “Reduced lateral resistance of abutment piles near MSE walls based on full-scale tests,” International Journal of Geotechnical Engineering, Vol. 6, No. 2, pp. 245-250, 2012. [9] J. S. Price,“Lateral resistance of piles near vertical MSE abutment walls,” M.Sc. thesis, Department of Civil and Environmental Engineering, Brigham Young University,Provo, UT, USA, 2012. [10] American Society of Testing and Material (ASTM),“Standard Test Method for Particle Size- Analysis of Soils”, ASTM (D422-2001), West Conshohocken, Pennsylvania, USA, 2006. [11] American Society of Testing and Material (ASTM),“Standard Test Method for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table”, ASTM D4253-00, West Conshohocken, Pennsylvania, USA,2006. [12] American Society of Testing and Material (ASTM), “Standard Test Method for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density”, ASTM D4254-00, West Conshohocken, Pennsylvania, USA, 2006. | ||
|
Statistics Article View: 345 PDF Download: 426 |
||