- All Journals
- Al-Qadisiyah University
- Basrah University
- Kirkuk University
- Mosul University
- The Iraqi Borad for Medical Specialization
- University of Anbar
- University of Technology
- Al Mustafa University
- Al-Zahraa University for Women
- Alnoor University
- Kunooz University
- Misan University
- Ninevah University
- Tikrit University
- University of Al-Hamdaniya
- University of Kerbala
Study of the Barreling of Copper Solid and Hollow Cylinders under Uniaxial Compressive Load | ||
| Engineering and Technology Journal | ||
| Article 15, Volume 38, 4A, 2020, Pages 614-621 PDF (737.75 K) | ||
| DOI: 10.30684/etj.v38i4A.306 | ||
| Author | ||
| Abdullah D. Assi* | ||
| Middle Technical University/Institute of Technology-Baghdad | ||
| Abstract | ||
| In this study, the effect of axisymmetric compression of cylindrical blocks of copper on diameter ratio, height reduction ratio and aspect ratio was noted. The effects of these non-dimensional parameters are very significant to the geometry of barreling throughout the process of plastic deformation of a cylinder under axial compression. The barreling effect was studied for solid and hollow copper cylindrical blocks having different dimensions. The relationship between the parameters was also studied. The practical results obtained were compared with some of the existing theories, and there was a good correlation of the results with these theories. | ||
| Keywords | ||
| Barreling; copper cylindrical; aspect ratio; uniaxial | ||
| References | ||
|
[1] N. C. Mehta, Viral V. Shiyani & Jemish R. Nasit, “Metal forming analysis,” International Journal of Emerging Technology and Advanced Engineering, vol. 3, Issue 5, May 2013. [2] M.J. Jweeg, M. H. Tlafeh, A.D. Assi, “The design and Manufacturing of a hydrostatic extrusion apparatus for Compound Cylinders from Al and Mg,” Diyala Journal of Engineering Sciences, vol. 6, no. 2, pp 86-103, 2013. [3] G.W. Rowe, “Principles of industrial metalworking processes,” Edwar Arnold, 1977. [4] M.J. Jweeg, M. H. Tlafeh, A.D. Assi, “Evaluation of a new hypothetical concept (LHSIR) for die profile design for hydrostatic extrusion of Al/Mg compound,” Diyala Journal of Engineering Sciences, vol. 7, No. 1, pp 40-61, 2014. [5] L. D. Dugandzic, “Hot impression die forging process parameter development for production of 6061 aluminum alloy medallions,” Report, California Polytechnic State University, 2004. [6] R.R. Raja, S.L. Lakshminarasimhan and P.M. Murugesan, “Investigation of barreling radius and top surface area for cold upsetting of aluminum specimens,” International Journal of Modern Engineering Research (IJMER), vol. 3, Issue. 6, pp. 3852-3862, 2013. [7] K.B. Baskaran and R.N. Narayanasamy, “An experimental investigation on work harding behavior of elliptical shaped billets of aluminum during cold upsetting,” Materials and Design, vol. 29, issue 6, pp. 1240–1265, 2008. [8] T.A. Altinbalik, “An experimental study of barreling and fem based simulation in cold upsetting of aluminum,” International Journal of Modern Manufacturing Technologies, ISSN 2067–3604, vol. III, no. 1, 2011. [9] K. B. Baskaran and R.N. Narayanasamy, “Some aspects of barreling in elliptical shaped billets of aluminum during cold upset forging with lubricant,” Materials and Design, pp. 638–661, 2008. [10] T.A. Altinbalik & Y.C. Can, “An upper bound analysis and determination of the barreling profile in upsetting,” Indian Journal of Engineering & material Sciences, IJEMS, vol. 18, no. 6, pp. 416-424, 2011 | ||
|
Statistics Article View: 308 PDF Download: 233 |
||