- All Journals
- Al-Qadisiyah University
- Basrah University
- Kirkuk University
- Mosul University
- The Iraqi Borad for Medical Specialization
- University of Anbar
- University of Technology
- Al Mustafa University
- Al-Zahraa University for Women
- Alnoor University
- Kunooz University
- Misan University
- Ninevah University
- Tikrit University
- University of Al-Hamdaniya
- University of Kerbala
Effect of Different Laser Welding Parameter on Welding Strength in Polymer Transmission Welding Using Semiconductor | ||
| Engineering and Technology Journal | ||
| Article 14, Volume 38, 5A, 2020, Pages 761-768 PDF (673.46 K) | ||
| DOI: 10.30684/etj.v38i5A.368 | ||
| Authors | ||
| Farah M. Shaker* 1; Mohanned M. AL-Khafaji2; Kadhim A. Hubeatir | ||
| 1Affiliation: Laser and Optoelectronics Engineering Department, University of Technology, Baghdad, Iraq | ||
| 2Department of Production Engineering and Metallurgy, University of Technology, Baghdad, Iraq. | ||
| Abstract | ||
| In this work, the diode laser (810μm wavelength) was used for laser transmission welding application on PMMA (polymethylmethacrylate). The welding was done between opaqueness and transparent with thickness 2 mm and 2.57 mm, respectively. The effects of different process parameters, laser speed, spot size and force with different values (5, 15, 20 mm/min), (2, 2.5, 3mm) and (2, 6, 10 N) respectively were used to study their effect on weld width and strength. L9 Taguchi orthogonal array has been used to design the experiments and optimize the result. The result of the signal to noise ratio shows that, the width of welding decrease with increasing both the welding speed and the spot size while it was increased with increasing the force on the sample. The narrower width observed at speed (20mm/min), spot size (3mm), and force (2N). Also, the best strength was found at speed (15 mm/min), spot size (2.5mm), and force (10N). | ||
| Keywords | ||
| polymer; Laser Transmission Welding; Taguchi technique; Weld Width. Weld Strength | ||
| References | ||
|
[1] M. Tim A. Osswald, Ing. Georg, ”Material science of polymers for engineers,” 3rd Editio. Munich: Hanser Publishers, 2010. [2] R. Klein, ”Laser welding of plastics,” 1st editio. Weinheim, Germany: Wiley-VCH Verlag & Co. KGaA, 2011. [3] S. T. A. M. Ilho, ”Feasibility study of metal to polymer hybrid joining,” Vol.24, No.3 March 2011, pp. 233–249. [4] N. L. Sekou Singare, S. Chen, J. Zou, “Laser transmission welding of thermoplastic: experimental investigation using polycarbonate,” Futur. Mater. Manuf. Mater. Process., Vol. 1091, pp. 63–69, 2015. [5] B. Acherjee, A. S. Kuar, S. Mitra, D. Misra, and S. Acharyya, ”Experimental investigation on laser transmission welding of PMMA to ABS via response surface modeling,” Opt. Laser Technol., Vol. 44, No. 5, pp. 1372–1383, 2012. [6] Rana M,Taha, “Through transmission laser welding of polymers using 1064 nm CW diode laser,” Int. J. Mod. Eng. Res., Vol. 2, pp. 3186–3189, 2012. [7] B. Acherjee, A. S. Kuar, S. Mitra, and D. Misra, “Integrating taguchi method with desirability function analysis to optimize the laser transmission welding process,” Am. Inst. Phys., Vol. 480, pp. 1–7, 2010. [8] M. Mehrpouya, A. Gisario, A. Rahimzadeh, and M. Barletta, “An artificial neural network model for laser transmission welding of biodegradable polyethylene terephthalate / olyethylene vinyl acetate ( PET / PEVA ) blends,” Int. J. Adv. Manuf. Technol., pp. 1–11, 2019. [9] P. R. Brown N, Kerr D, Jackson M, “Laser welding of thin polymer films to container substrates for aseptic packaging,” Opt Laser Technol, Vol. 32, pp. 139–146, 2000. [10] M. W., M. Gordon, “Application studies using through - transmission laser welding of polymers,” Proceedings of the Conference Joining Plastics, London, 2006. [11] H. Y. Z. Y. H. Chen, S. C. Tam, W. L. Chen, “Application of taguchi method in the optimization of laser micro-engraving of photomasks,” Int. J. Mater. Prod. Technol, Vol. 11, pp. 1–9, 1996. [12] A. Jmp, “Design of experiments,” Second E. USA: the United States of America. For: SAS Institute Inc., Cary, NC, 2009. [13] S. L. Campanelli, G. Casalino, N. Contuzzi, and A. D. Ludovico, “Taguchi optimization of the surface finish obtained by laser ablation on selective laser molten steel parts,” Procedia CIRP, Vol. 12, pp. 462–467, 2013. [14] R. Rudrapati, N. Kumar, and P. K. Pal, “Application of taguchi method for parametric optimization of through transmission laser welding of acrylic plastics,” in AIP Conference Proceedings 2057, 020013, Vol. 020013, pp. 1–8, 2019. | ||
|
Statistics Article View: 362 PDF Download: 319 |
||