Effect of Radial Clearance on Stress and Strain Distribution in the Astral Deep Drawing

Jawad, Waleed K.; Ikal, Ali T.

doi:10.30684/etj.37.8A.4

	Effect of Radial Clearance on Stress and Strain Distribution in the Astral Deep Drawing
Engineering and Technology Journal
Article 4, Volume 37, 8A, 2019, Pages 332-340 PDF (1.07 M)
Document Type: Research Paper
DOI: 10.30684/etj.37.8A.4
Authors
Waleed K. Jawad; Ali T. Ikal
Production and Metallurgy Engineering Department, University of Technology - Iraq
Abstract
In this paper, an astral die was designed and constructed to produce an astral cup in the deep drawing operation by experimental work and numerical simulation. The influence of radial clearance on drawing load, cup high, the distribution of stress, strain and thickness along the side wall, minor and major axis were also studied. The deep drawing process was carried out to produce an astral cup with an inner dimension of (41.5mm × 34.69mm), and (30mm) height drawn from a blank sheet with a thickness of (0.7) and diameter (80) made of low carbon steel. A commercial program (ANSYS18.0) was used to perform the numerical simulation. Three types of radial clearance equal to (1.1 , 1.2 , and 1.3 ) are used to investigate the influence of radial clearance. It was found that the maximum value of the drawing load 55KN) recorded with radial clearance equal (1.1 ). The process of a squeeze in the wall that occurred with the radial clearance (1.1 ) due to the difficulty of the flow of the metal to be exposed to maximum tensile stress. The maximum effective stress (674MPa) and strain (0.973) were recorded with the clearance of (1.1 ) at the minor axis.
Keywords
deep drawing of the astral shape; stress and strain distribution; radial clearance

References
[1] N.S.M. Namer, S.A. Nama, and J.W. Thabit, “Numerical and Experimental Study on Deep Drawing Process for AA2024-T4 Sheet,” Journal of Applied and Experimental Mechanics, Vol. 1, Issue. 1, pp. 1–9, 2015. [2] R. Padmanabhan, M.C. Oliveira, J.L. Alves, and L.F. Menezes, “Influence of process parameters on the deep drawing of stainless steel,” Journal of Materials Processing Technology, Vol.43, pp. 1062 – 1067, 2007. [3] H. Zein, M. El-Sherbiny, M. Abd-Rabou, and M. El Shazly, “Effect of Die Design Parameters on Thinning of Sheet Metal in the Deep Drawing Process,” American Journal of Mechanical Engineering, Vol.1, No. 2, pp. 20- 29, 2013. [4] A.C.S. Reddy, S. Rajesham, P.R. Reddy, and T.P. Kumar, “An experimental study on the effect of process parameters in deep drawing using Taguchi technique,” International Journal of Engineering, Science and Technology, Vol.7, No. 1, pp. 21-32, 2015. [5] H.A Ameen, and O.H. Abdulridha, “Effect of Clearance and Blank Thickness on Stress Distribution in Elliptical Deep Drawing without Blank Holder using ANSYS,” International Journal of Engineering Research & Technology, Vol.50, Nol.5, Issue.1, pp. 360–366, 2016. [6] W.K. Jawed and S.S. Dawood “Drawing of Hexagonal Cup,” Eng. &Tech. Journal, Vol.34, No. 7, pp. 1445-1456, 2016. [7] A.I.O. Zaid and F.A. Hashim, “Effect of Punch and Die Profile Radii on Deep Drawing of Galvanized Steel,” International Journal of Applied Research in Mechanical Engineering, Vol.1, Issue-1, pp. 17–23, 2017. [8] M. Mahmoodi and H. Sohrabi, “Using the Taguchi Method for Experimental and Numerical Investigations on the Square-Cup Deep-Drawing Process for Aluminum/Steel Laminated Sheets,” Mechanics of Advanced Composite Structures, Vol, pp. 169-177, 2017. [9] A.K. Choubey, G. Agnihotri and C. Sasikumar, “Experimental and mathematical analysis of simulation results for sheet metal parts in deep drawing,” Journal of Mechanical Science and Technology, Vol. 31, No. 9, pp. 4215-4220, 2017. [10] S.J.H. Nejad1, R. Hasanzadeh, A. Doniavi, and V. Modanloo, “Finite element simulation analysis of laminated sheets in deep drawing process using response surface method,” International Journal of Advanced Manufacturing Technology, Vol. 4, Nol.1, pp. 1-6, 2017.
Statistics Article View: 341 PDF Download: 367