- All Journals
- Al-Qadisiyah University
- Basrah University
- Kirkuk University
- Mosul University
- The Iraqi Borad for Medical Specialization
- University of Anbar
- University of Technology
- Al Mustafa University
- Al-Zahraa University for Women
- Alnoor University
- Kunooz University
- Misan University
- Ninevah University
- Tikrit University
- University of Al-Hamdaniya
- University of Kerbala
Effect of Potassium Chloride and Potassium Sulphate Electrolyte Solutionon Surface Roughnessand Material Removal Rate in Electro Chemical Machining (ECM) | ||
| Engineering and Technology Journal | ||
| Article 5, Volume 37, 8A, 2019, Pages 341-347 PDF (609.44 K) | ||
| Document Type: Research Paper | ||
| DOI: 10.30684/etj.37.8A.5 | ||
| Authors | ||
| Heba S. Qasim1; Shukry H. Aghdeab2 | ||
| 1Production Engineering and Metallurgy Dept., Iraq | ||
| 2Department of Production Engineering and Metallurgy, University of Technology, Baghdad, Iraq, | ||
| Abstract | ||
| Electrochemical machining (ECM) is nontraditional machining which is used to remove metal by anodic dissolution. In this study the metal workpiece (WP) was stainless steel (AISI 316) and potassium chloride (KCl) and potassium sulphate (K2SO4) solutions were used as electrolyte, and the tool was used from copper. In this work the experimental parameters that used were concentration of solution, current and voltage as input. While surface roughness (Ra) and material removal rate (MRR) were the output. The experiments on electrochemical machining with using concentration (10, 20 and 30) g/l, current (2, 5 and 10) A and voltage (6, 12 and 20)V. Gap size between tool and WP (0.5) mm. The results showed that (K2SO4) solution gave surface roughness and material removal rate less than (KCl) solution in all levels, maximum (Ra) is (0.471) and minimum (0.049), while (KCl) solution gave maximum (Ra) was (4.497) and minimum was (0.837). Generally increasing in machining parameter (concentration of solution, current and voltage) lead to increase in (Ra) and (MRR). This study aims to compare the effect of using different electrolyte solution including potassium chloride (KCl) and potassium sulphate (K2SO4) on the surface roughness (Ra) and material removal rate (MRR). | ||
| Keywords | ||
| electro-chemical machining; Surface Roughness; concentration of solution | ||
| References | ||
|
[1] X. Fang, N. Qu, H. Li and D. Zhu, “Enhancement of insulation coating durability in electrochemical drilling,” Int J Adv Manuf Technol, Vol. 68, pp. 9–12, 2005–2013. [2] E.S. Lee, “International Journal of Advanced Manufacturing Technology, Chapter 16, pp. 591-599, 2000. [3] F. Phillip and O.J. Muñoz, “Manufacturing Process and System,” Ninth edition, Chapter 20, Published Simultaneously Canada, pp.482-483, 1997. [4] R. Ganjir, “Optimization of Process Parameters in ECM by Using Rotary U Shaped Tool,” M.Sc. Thesis, National Institute of Technology, India, pp.1-65, 2010. [5] S.J. Lee, C.P. Liu, T.J. Fan, and Y.H. Chen, International Journal of Electrochemical Science, Chapter 8, pp. 1713-1721 , 2013. [6] M.K. Das, K. kumar and T. Kr, “Artificial Neural Networks Modeling for the Predication of Surface Roughness in ECM,” International Journal of Applied Engineering Research, Vol.9, No.26, PP.9251-9254, India, 2014. [7] Sh. Hammed, A. Mustafa and K. Safaa, “Optimization of Surface Roughness for Al-alloy in Electro-chemical Machining (ECM) Using Taguchi Method,” Journal of Engineering Vol. 23, pp. 62-71, 2017. [8] A.J. Unare1, P.R. Attar, “Optimaization of process parameter of electrochemical machining of aluminum alloy 7075 by using gray touchy,” International Research Journal of Engineering and Technology, Vol. 03, 2016. [9] H. Al-Hofy, “Advanced Machining Process, Nontraditional and Hybrid machining,” First Edition, Chapter 4, McGraw-Hill Company, Egypt, pp. 77-99, 2005. [10] H.H. Alwan, “Study of Some Electrochemical Machining Characteristics of Steel Ck35,” M.Sc. Thesis, University of Technology, Iraq, 2011. [11] U. Mallick, “Estimation of MRR by using Ushape Electrode in Electrochemical Machining,” M.Sc. Thesis, National Institute Technology, India, 2009. [12] M.K. Singh, “Unconventional Manufacturing Process,” First edition, new age international publishers, New Delhi, 2008. [13] B. Bhattacharyy, M. Malapati, J. Munda, A. Sarkar, “Influence of tool vibration on machining performance in electrochemical micro-machining of copper,” Journal of material processing technology, vol. 47, pp.335 – 342, 2007. [14] U. Rath, “Two Phase Flow Analysis In Electrochemical Machining For L-Shaped Tool,” Department of Mechanical Engineering National Institute of Technology Rourkela, M.Sc Thesis, National Institute of Technology, India, pp.1-109, 2013. | ||
|
Statistics Article View: 341 PDF Download: 448 |
||