Effect of laser Peening on the Microhardness and Roughness of Al-7277 alloy

[1] C. Vargel, “Corrosion of Aluminum, “Elsevier
Science. San Diego, USA. 2004.
[2] C.N. Panagopoulos, E.P. Georgiou, A.G. Gavras,
“Corrosion and wear of 6082 aluminum alloy,” Tribol
.int.42, 6, 886-889, 2009.
[3] J.B. Bajat et al., “Corrosion protection of aluminum
pretreated by vinyltriethoxysilan in sodium in sodium
chloride solution' corros .Sci .52, 3, 1060-1069, 2010.
[4] C. Rubio-Gonzleza, C. Felix-Martineza, G. GomezRosasb, J.L. Ocanac, M. Moralesc and J.A. Porroc “Effect
of laser shock processing on fatigue crack growth of
duplex stainless steel,” Materials Science and Engineering
A 528, 914- 919, 2011.
[5] M.A. Montealegre and C. Materials, “Surface
Treatments by Laser Technolgy,” 1, 19–30, 2010.
[6] P. Peyre, L. Berthe, X. Scherpereel and R. Fabbro
“Laser-shock processing of aluminium-coated 55C1 steel
in water-confinement regime, characterization and
application to high-cycle fatigue behavior,” Journal of
Materials Science, 33, 1421 – 1429, 1998.
[7] D. Schuocker, Handbook of the Eurolaser Academy,
Ed. Chapman-Hall, 1998.
[8] W.M. Steen, “Laser Material processing,” Springer,
2003.
[9] S. Sathyajith, S. Kalainathan, and S. Swaroop, “Laser
peening without coating on aluminum alloy Al-6061-T6
using low energy Nd: YAG laser,” Opt. Laser Technol.,
45, 1, 389–394, 2013.
[10] S. Matthew and craig .B “Fundamentals of laser –
material intracction and application to multiscale surface
modification,” CH.2, p91-104, Princeton university-USA
2010.
[11] Y. Zhang et al. Chapter 2, “Surface Integrity of LY2
Al Alloy Subjected to Laser Shock Processing,” Springer
Series in Materials Science 179, DOI: 10.1007/978-3-642-
35674-2-2, Berlin Heidelberg, 2013.
[12] A. Kadhim, E.T. Salim, S. M. Fayadh, A.A. AlAmiery, “Effect of Multipath Laser Shock Processing on
Microhardness, Surface Roughness, and Wear Resistance
of 2024-T3 Al Alloy,” The Scientific World Journal
Volume, Article ID 490951,6 pages., 2014.
[13] U. Trdan, J.L. Ocaña, J. Grum, “Surface Modification
of Aluminium Alloys with Laser Shock Processing,”
Strojniški vestnik - Journal of Mechanical Engineering
575, 385-393., 2011.
[14] H.T. Hussein, A. Kadhim, A.A. Al-Amiery,
“Enhancement of the Wear Resistance and Microhardness
of Aluminum Alloy by Nd:YAG laser treatment, Scientific
World Journal, Article ID 842062, 5 pages., 2014.
[15] Y. Hu and Z. Yao “Numerical simulation and
experimentation of overlapping laser shock processing
with symmetry cell,” International Journal of Machine
Tools & Manufacture 48, 152–162., 2010.
[16] G. Gomez-Rosasa, C. Rubio-Gonzalezb, J. L. Ocanac,
C. Molpeceresc, J.A. Porroc, M. Moralesc and F.J. Casillas
“Laser Shock Processing of 6061-T6 Al alloy with
1064nm and 532nm wavelengths,” Applied Surface
Science 256, 5828–5831, 2010.