Investigation the Effect of Negative Polarity of Surface Roughness and Metal Removal Rate During EDM Process

Taqi, Shahd A.; Shather, Saad K.

doi:10.30684/etj.v38i12A.1591

	Investigation the Effect of Negative Polarity of Surface Roughness and Metal Removal Rate During EDM Process
Engineering and Technology Journal
Article 12, Volume 38, 12A, 2020, Pages 1852-1861 PDF (1.11 M)
Document Type: Research Paper
DOI: 10.30684/etj.v38i12A.1591
Authors
Shahd A. Taqi^* ¹; Saad K. Shather²
¹Production engineering and metallurgy department, university of technology, Baghdad, Iraq
²Production engineering and metallurgy department, university of technology, Baghdad, Iraq.
Abstract
The Electro discharge machine that named (EDM) is used to remove the metal from the workpiece by spark erosion. The work of this machining depends on the multiple variables. One of the most influential variants of this machine is the polarity, the material of the electrode, the current and the time pulses. Essentially the polarity of the tool (electrode) positive and the work piece is negative, this polarity can be reversed in this paper was reversed the polarity that was made the tool (electrode) negative and the work piece was positive. The aim of this paper was focused on the influence of reversed the polarity (negative) with changing the electrode metal (copper and graphite) on the surface roughness and metal removal rate by using different parameters (current and pulses of time). Experiments show that: the copper electrode gives (best surface roughness 0.46 μm when the current 5 Am and Ton 5.5 μs) and (worst surface roughness 1.66 μm when the current is 8 A and Ton 25 μs). And give (best values of the MRR 0.00291 g/min when the current is 8 and Ton 25 μs) and (The lowest values of MRR (0.00054 g/min when current is 5 and Ton 5.5 μs). The graphite electrode gives (best surface roughness 2.07 μm when the current 5 Am and Ton 5.5 μs) and (worst surface roughness 4.17 μm when the current is 8 A and Ton 25 μs). And give (best values of the MRR 0.05823 g/min when the current is 8 and Ton 25 μs) and (The lowest values of MRR (0.00394 g/min when current is 5 and Ton 5.5 μs).
Keywords
EDM; Revers Polarity; Electrode Metal; MRR; Surface roughness (Ra)

References
[1] A. Begum, and D. R. Reddy, “Effect of polarity on the machining characteristics and surface generation in EDM,” Materials Today: Proceedings 4, no. 8, 7674-7679, 2017. [2] B. P. Gavali, C. A.Waghmare and S. S. Kalashetty, “Experimental investigation of changing polarity in powder mixed electric discharge machining (PM-EDM),” International Journal of Engineering and Technology, vol. 8, no. 5, pp. 2049–2058, 2019. [3] S. K. Shather, “Improving the metal removal rate (MRR) in electro discharge machining by additives powder,” Engineering and Technology Journal 34, no. 14 Part (A) Engineering, 2766-2774, 2016. [4] A. Begum, and R. Reddy, “Effect of polarity on the machining characteristics and surface generation in EDM,” Materials Science and Engineering, Vol. 4, no. 8, Pages 7674-7679, 2017. [5] S. A. Taqi, S. K. Shather, “Influence of polarity of electro discharge machine (EDM) on surface roughness (sr) and metal removal rate (mrr) of low carbon stee,” Engineering and Technology Journal, Vol. 38, Part A, No. 07, Pages 975-983, 2020. [6] L. Praveen, P. G. Krishna, L. Venugopal, and N. E. C. Prasad, “Effects of pulse ON and OFF time and electrode types on the material removal rate and tool wear rate of the Ti-6Al-4V Alloy using EDM machining with reverse polarity, ” In IOP Conference Series: Materials Science and Engineering, vol. 330, no. 1, p. 012083. IOP Publishing, 2018. [7] P.B. Gavali, C. A.Waghmare and S. S. Kalashetty “Experimental investigation of changing polarity in powder mixed electric discharge machining (PM-EDM),” International Journal of Engineering and Technology (IJET), vol. 8, no. 5, 2016. [8] Md. A. R. Khan, and M.M. Rahman, “Surface characteristics of Ti-5Al-2. 5Sn in electrical discharge machining using negative polarity of electrode,” International Jornal Of Advanced Manufacturing Technology, vol. 92, pp. 1-13, 2017. [9] I. Santos, M.I. Poli, and D. Hioki “influence of input parameters on the electrical discharge machining of titanium alloy (TI-6AL-4V),” International Journal of Manufacturing Research, 10(3):286, 2015,2015. [10] M. Galai, M. Rbaa, Y. E. Kacimi, M. Ouakki, N. Dkhirech, R. Touir, B. Lakhrissi and M. E. Touhami, “Anti-corrosion properties of some triphenylimidazole substituted compounds in corrosion inhibition of carbon steel in 1.0 M Hydrochloric Acid Solution,” Analytical and Bioanalytical Electrochemistry, vol. 9, no. 1, pp. 80-101, 2017. [11] L Praveen, P Geeta Krishna, L Venugopal and N. E. C. Prasad, “Effects of pulse ON and OFF time and electrode types on the material removal rate and tool wear rate of the Ti-6Al-4V Alloy using EDM machining with reverse polarity, ” IOP Conf. Series: Materials Science and Engineering, vol. 330, 2018. [12] H. B. Özerkan, “Effect of changing polarity of graphite tool/ Hadfield steel work piece couple on machining performances in die sinking EDM, ” MATEC Web of Conferences ICMTMTE, vol. 129, 2017.
Statistics Article View: 495 PDF Download: 250