Effect of Voltage on Electrode Wear Rate (EWR) in the Electrical Discharge Machining (EDM) for Stainless Steel AISI 444

Aghdeab, Shukry H.; Abdulnabi, Anwer Q.

doi:10.30684/etj.v40i6.2144

	Effect of Voltage on Electrode Wear Rate (EWR) in the Electrical Discharge Machining (EDM) for Stainless Steel AISI 444
Engineering and Technology Journal
Article 3, Volume 40, Issue 6, 2022, Pages 855-861 PDF (827.63 K)
Document Type: Research Paper
DOI: 10.30684/etj.v40i6.2144
Authors
Shukry H. Aghdeab^* ¹; Anwer Q. Abdulnabi²
¹Production Engineering and Metallurgy Department, University of Technology - Iraq
²Production Engineering Dept., University of Technology-Iraq, Alsina’a Street, 10066 Baghdad, Iraq.
Abstract
Electrical Discharge Machining process (EDM) is a nontraditional metal removal technique that uses thermal energy to erode the workpiece without generating any physical forces of cutting between the tool and the machining part. It is used to cutting of hard and electrical conductivity materials and product intricate shapes of products. The aim of this work is to study the effect of changing voltage values on electrode wear rate (EWR). The machining parameters includes voltage (V), peak current (Ip), pulse duration (Ton) and finally, pulse interval (Toff). The results show that the EWR was increase with rising in voltage, peak current and pulse duration values but when the pulse interval value rises, the electrode wear rate reduce. The best (EWR) value was (0.093507) mm3/min that obtained at voltage (140) V, Ip (12) A, Ton (400) µs and Toff (12) µs.
Highlights
Using low levels of machining parameters (voltage, Ip and Ton) to achieve low EWR. According to Factorial Design, model fits the data was 97.65% and 97.83% for 140 and 240 V, respectively. Mathematical relationship between the input parameters and EWR has been gained for correlating EWR.
Keywords
Electrical discharge machining (EDM); EWR; Voltage values; Full factorial

References
[1] S. K. Choudhary and R. S. Jadoun, Current research issue, trend and applications of powder mixed dielectric electric discharge machining (PM-EDM): A Review, Int. J. of Eng. Sci. and Res. Tech., 7 (2014) 335-358. [2] A. kumar and Khempal, Key engineering of electrical discharge machining: A review, Int. J. for Res.in Appl. Sci. and Eng. Tech., 7 (2015) 384-395. [3] S. K. Dewangan, Experimental investigation of machining parameters for EDM using U-shaped electrode of AISI P20 tool steel, M.Sc. Thesis, Dept. of Mechanical Engineering, National Institute of Technology Rourkela, India, 2010. [4] P. Mishra and L. P. Singh, Experimental study of process parameters in EDM using tool steel electrode, Int. J. Eng. Sci. and Res. Tech., 9 (2017) 309-313. [5] B. M. Schumacher, R. Krampitz and J. P. Kruth, Historical phases of EDM development driven by the dual influence of Market Pull and Science Push, Science Direct, 6 (2013) 5-12 . [6] R. Vishwakarma, S. K. Yadav, A. Kumar and H. Krishna, Effect of different electrodes and dielectric fluids on metal removal rate and surface integrity of electric discharge machining: A review, Int. J. Eng. Tech. Sci. and Res., 11 (2017) 935-941 . [7] S. T. Ganapati, M. S. Apachapuri and C. V. Adake, Influence of process parameters of electrical discharge machining on MRR, TWR and surface roughness: A Review, International Conference on Advances in Mechanical Engineering and Nanotechnology, 2148, 1 (2019) 1-7. [8] B. V. Kumar and D. J. Jyothsna Devi, Optimization of die-sinking EDM process parameters with steel electrodes using ANOVA. International Journal of Computational Engineering Research, 6 (2018) 60-66. [9] S. H. Aghdeab, W. I. Mahdi AL- Tameemi and A. F. Jawad, Study the effect of electrode wear weight (EWW) in electrical discharge machining (EDM), Eng. and Tech. Journal, 32 (2014) 1433-1441 . [10] S. ľuboslav and H. Slavomíra, Study of tool electrode wear in EDM Process, Key Engineering Materials, 669 (2016) 302-310. [11] J. Jeevamalar and S. Ramabalan, Die sinking EDM process parameters: A Review, Int. J. of Mech. Eng. and Rob. Res., 1 (2015) 315-326. [12] B. Nahak and A. Gupta, A review on optimization of machining performances and recent developments in electro discharge machining, Manufacturing Review, 6 (2019) 1-22. [13] P. M. George, B. K. Raghunath, L. M. Manocha and Ashish M. Warrier, EDM machining of carbon carbon composite- a taguchi approach, J. of Mat. Proc. Tech., 145 (2004) 66-71. [14] S. Daneshmand, E. F. Kahrizi, E. Abedi and M. M. Abdolhosseini, Influence of machining parameters on electro discharge machining of NiTi shape memory alloys. Int. J. Electrochemical Science, 8 (2013) 3095-3104. [15] K. G. Maniyar, Roshan V. Marode and S. B. Chikalthankar, Optimization of EDM process parameters on MRR & TWR of tungsten carbide by taguchi method, Int. J. of Eng. and Adv. Tech., 3 (2016) 112-116 . [16] K. Kakkar, N. Rawat, A. Jamwal and A. Aggarwal, Optimization of surface roughness, material removal rate and tool wear rate in EDM using taguchi method. International Journal of Advance Research, Ideas and Innovations in Technology, 2 (2018) 16-24. [17] A. A. Khleif and O. S. Sabbar, Electrode wear evaluation in E.D.M process, Eng. and Tech. J., 37 (2019) 252-257. [18] S. M. Basha, H. K. Dave and H. V. Patel, Experimental investigation of jatropha curcas bio-oil and biodiesel in electric discharge machining of Ti-6Al-4V, Materials Today: Proceedings, 38 (2020) 2102-2109. [19] D. W. Jung, Effects of Input Parameters on Electrode Wear Rate when EDM Cylindrical Shaped Parts, Material Science and Engineering, 1018 (2021) 79-83.
Statistics Article View: 431 PDF Download: 407