- All Journals
- Al-Qadisiyah University
- Basrah University
- Kirkuk University
- Mosul University
- The Iraqi Borad for Medical Specialization
- University of Anbar
- University of Technology
- Al Mustafa University
- Al-Zahraa University for Women
- Alnoor University
- Kunooz University
- Misan University
- Ninevah University
- Tikrit University
- University of Al-Hamdaniya
- University of Kerbala
The Experimental Impact of Convective Heat Transfer Improvement from Numerous Perforated Shape Fin Array | ||
| Al-Rafidain Engineering Journal (AREJ) | ||
| Article 26, Volume 28, Issue 1, 2023, Pages 280-292 PDF (1.61 M) | ||
| Document Type: Research Paper | ||
| DOI: 10.33899/rengj.2022.136544.1209 | ||
| Authors | ||
| Noori Raad Noori1; Arkan Fawzi Saeed* 2 | ||
| 1Power Engineering Department, University of Polytechnic-Duhok, Duhok, Iraq | ||
| 2Mechanical Engineering Department, College of Engineering, University of Duhok, Duhok, Iraq | ||
| Abstract | ||
| The current work explores a trial forced convective heat move from rectangular blades on an upward surface at low Reynolds numbers. The heat removal for a proper number of punctured and non-punctured fins, fin dividing, and length was estimated in an upward air stream for fluctuating inlet air speed and some way or another low info heat power somewhere in the range of 20W and 70W. The characteristics are investigated for rectangular, circular, and V-shape perforated fin array against non-perforated one. The impact of different boundaries, like heat input with various liquid stream speed on average coefficient of heat transfer (h) improvement has been considered. The impact of the Nusselt numberand Reynolds number, were practically examined. The heat loss has been improved by increasing the heat transfer coefficient between the fin total surface and its encompassing, through increasing the area of heat to remove all out surface through fin perforations. The trial relations have been differentiated by correlating Nu and Re for non-punctured plate heat sink, the reach 6*103 £ Re £ 19*103, and Pr @ 0.7 with error ±7%, and punctured finned plate heat sink with the reach 6*103 £ Re £ 20*103, and Pr @ 0.7 with a deviation factor R2=0.995. | ||
| Keywords | ||
| Forced convection. Heat transfer enhancement. Perforated Fin | ||
| References | ||
|
[1] O. Sara, T. Pekdemir, S. Yapici, and M. Yilmaz, “Heat-transfer enhancement in a channel flow with perforated rectangular blocks,” International Journal of Heat and Fluid Flow, vol. 22, no. 5, pp. 509–518, 2001. [2] U. Akyol and K. Bilen, “Heat transfer and thermal performance analysis of a surface with hollow rectangular fins,” Applied Thermal Engineering, vol. 26, no. 2–3, pp. 209–216, 2006. [3] K. H., “Thermal Analysis of Square and Circular Perforated Fin Arrays by Forced Convection,” International Journal of Current Engineering and Technology, vol. 2, pp. 109–114, Jan. 2013, doi: 10.14741/ijcet/spl.2.2014.20. [4] T. K. Ibrahim et al., “Experimental study on the effect of perforations shapes on vertical heated fins performance under forced convection heat transfer,” International Journal of Heat and Mass Transfer, vol. 118, pp. 832–846, 2018. [5] M. Mohammad, M. P. H. Talukder, K. A. Rahman, and M. W. Hridoy, "Experimental Investigation on the Effect of Different Perforation Geometry of Vertical Fins Under Forced Convection Heat Transfer," in International Conference on Mechanical Engineering and Renewable Energy, 11-13 Dec 2019. [6] R. Adhikari, D. Wood, and M. Pahlevani, “An experimental and numerical study of forced convection heat transfer from rectangular fins at low Reynolds numbers,” International Journal of Heat and Mass Transfer, vol. 163, p. 120418, 2020. [7] T. K. Ibrahim, A. T. Al-Sammarraie, M. S. Al-Jethelah, W. H. Al-Doori, M. R. Salimpour, and H. Tao, “The impact of square shape perforations on the enhanced heat transfer from fins: Experimental and numerical study,” International Journal of Thermal Sciences, vol. 149, p. 106144, 2020. [8] A. R. Kaladgi et al., “Heat transfer enhancement of rectangular fins with circular perforations,” Materials Today: Proceedings, vol. 47, pp. 6185–6191, 2021. [9] J. P. Holman, Heat transfer, 10th edition, McGraw-Hill, 2010. [10] J. F. Douglas, J. M. Gasiorex, J. A. Swaffield, and L. B. Jack, Fluid Mechanics, 5th edition, Prentice Hall, 2005. [11] A. F. SAEED and O. A. ABBO, “Design, and Manufacturing a Small-scale Wind Tunnel for Heat Transfer Analysis of Flat Plate and Finned Plate Heat Sinks,” Journal of Duhok University, vol. 23, no. 2, pp. 693–706, 2020. | ||
|
Statistics Article View: 839 PDF Download: 499 |
||