- All Journals
- Al-Qadisiyah University
- Basrah University
- Kirkuk University
- Mosul University
- The Iraqi Borad for Medical Specialization
- University of Anbar
- University of Technology
- Al Mustafa University
- Al-Zahraa University for Women
- Alnoor University
- Kunooz University
- Misan University
- Ninevah University
- Tikrit University
- University of Al-Hamdaniya
- University of Kerbala
Study the Forced Convection of a Hybrid Nanofluid in a Square Channel Partially Filled with a Porous Media Using the K-epsilon Turbulence Model | ||
| Kerbala Journal for Engineering Sciences (KJES) | ||
| Article 4, Volume 3, Issue 1, 2023, Pages 47-61 PDF (1.52 M) | ||
| Document Type: Research Article | ||
| DOI: 10.63463/kjes1077 | ||
| Authors | ||
| Sarmad A. Ali* 1; Suhad A. Rasheed2 | ||
| 1Department of Mechanical Engineering, University of Technology, Baghdad, Iraq | ||
| 2Department of Mechanical Engineering, University of Technology, Baghdad, Iraq | ||
| Abstract | ||
| The use of joint technologies to improve the heat transfer process in engineering and industrial applications enhances the heat transfer coefficient and Nusselt number, thus increasing its thermal efficiency and performance for these applications for example (air conditioning systems, solar energy systems, storage tanks, and heat exchangers). This paper presents a numerical simulation using (the k-epsilon turbulence) model to investigate the influence of forced convection heat transfer and fluid flow for a channel (square cross-section) of a length (50 cm), width of (12 cm), and height (12 cm) partially filled with height layer (8 cm) of the porous medium (Glass Spheres of diameter 5mm) with the addition of hybrid nanofluids (HNF) to the base fluid (Engine Oil) as a combined technique to obtain the best improvement, where the three- dimensional (3D) test model was designed using the commercial code COMSOL Multiphysics 6.0 program in two cases, the first does not contain any addition to the improvement, and the second contains the joint techniques (porous media and HNF), the governing equations for the turbulent flow of the fluid (mass conservation equation, momentum conservation equation, energy conservation equation) were solved. The results showed that the temperature, velocity, and pressure distribution of the base fluid in a test section increases significantly using these techniques and enhances the heat transfer coefficient compared to the results for the test section without these additions. In addition, the temperature distribution increases with the increase in the axial length of the fluid flow in the test section of the channel. The results of this study also showed that the porous material leads to obstruction of the fluid flow, and thus the thickness of the boundary layer decreases, and the shape of the temperature and velocity distribution changes along the test section. | ||
| Keywords | ||
| Forced Convection; Partially Filled; Hybrid Nanofluid; porous media; Square Channel; k-epsilon turbulence model | ||
| References | ||
|
[1] Iskandar Waini, Anuar Ishak, Teodor Groşan, and Ioan Pop "Mixed convection of a hybrid nanofluid flow along a vertical surface embedded in a porous medium." International Communications in Heat and Mass Transfer 114 (2020): 104565.
[2] Kaouther Ghachem, Walid Aich, and Lioua Kolsi. "Computational analysis of hybrid nanofluid enhanced heat transfer in cross flow micro heat exchanger with rectangular wavy channels." Case Studies in Thermal Engineering 24 (2021): 100822.
[3] Mohammad Ghazvini, and Hossein Shokouhmand. "Investigation of a nanofluid-cooled microchannel heat sink using Fin and porous media approaches." Energy conversion and management 50.9 (2009): 2373-2380.
[4] Mohsen Izadi, Mikhail A. Sheremet, and S. A. M. Mehryan. "Natural convection of a hybrid nanofluid affected by an inclined periodic magnetic field within a porous medium." Chinese Journal of Physics 65 (2020): 447-458.
[5] Kamel Milani Shirvan, Rahmat Ellahi, Soroush Mirzakhanlari, and Mojtaba Mamourian "Enhancement of heat transfer and heat exchanger effectiveness in a double pipe heat exchanger filled with porous media: Numerical simulation and sensitivity analysis of turbulent fluid flow." Applied Thermal Engineering 109 (2016): 761-774.
[6] P. R. Mashaei, M. Shahryari, and S. Madani. "Numerical hydrothermal analysis of water-Al2 O2 nanofluid forced convection in a narrow annulus filled by porous medium considering variable properties: Application to cylindrical heat pipes." Journal of Thermal Analysis and Calorimetry 126 (2016): 891-904.
[7] Huijin Xu. "Convective heat transfer in a porous-medium micro-annulus with effects of the boundary slip and the heat-flux asymmetry: an exact solution." International Journal of Thermal Sciences 120 (2017): 337-353.
[8] D. A. Nield, and Andrey V. Kuznetsov. "Thermal instability in a porous medium layer saturated by a nanofluid." International Journal of Heat and Mass Transfer 52.25-26 (2009): 5796-5801.
[9] Sabah R. Mahdi, and A. Suhad. "Experimental Study Convection Heat Transfer Inside the Triangular Duct Filled with Porous Media." Engineering and Technology Journal 41.01 (2023): 203-217.
[10] Kaouther Ghachem, Walid Aich, and Lioua Kolsi. "Computational analysis of hybrid nanofluid enhanced heat transfer in cross flow micro heat exchanger with rectangular wavy channels." Case Studies in Thermal Engineering 24 (2021): 100822.
[11] Israa Alesbe, Sahira Hasan Ibrahim, and Sattar Aljabair. "Mixed convection heat transfer in multi-Lid-driven trapezoidal annulus filled with hybrid nanofluid." Journal of Physics: Conference Series. Vol. 1973. No. 1. IOP Publishing, 2021.
[12] B. Ali, R.A. Naqvi, D. Hussain, O.M. Aldossary, S. Hussain, “Magnetic rotating flow of a hybrid nano-materials ag-mos2 and go-mos2 in c2h6o2-h2o hybrid base fluid over an extending surface involving activation energy: Fe simulation”, Mathematics 8 (10) (2020) 1730. | ||
|
Statistics Article View: 3,153 PDF Download: 518 |
||