Mohsein, Z., Abdulwahhab, A., Alkareem Noori, D. (2023). Influence of Cutting Parameter on Scarface Quality in Dry Turning of Different Materials. , 16(2), 96-101. doi: 10.30772/qjes.v16i2.850
Zainab Hussein Mohsein; Ahmed Basil Abdulwahhab; Diana Abed Alkareem Noori. "Influence of Cutting Parameter on Scarface Quality in Dry Turning of Different Materials". , 16, 2, 2023, 96-101. doi: 10.30772/qjes.v16i2.850
Mohsein, Z., Abdulwahhab, A., Alkareem Noori, D. (2023). 'Influence of Cutting Parameter on Scarface Quality in Dry Turning of Different Materials', , 16(2), pp. 96-101. doi: 10.30772/qjes.v16i2.850
Mohsein, Z., Abdulwahhab, A., Alkareem Noori, D. Influence of Cutting Parameter on Scarface Quality in Dry Turning of Different Materials. , 2023; 16(2): 96-101. doi: 10.30772/qjes.v16i2.850

Influence of Cutting Parameter on Scarface Quality in Dry Turning of Different Materials

Al-Qadisiyah Journal for Engineering Sciences
Volume 16, Issue 2, June 2023, Pages 96-101    PDF (584.51 K)
Document Type: Research Paper
DOI: 10.30772/qjes.v16i2.850
Authors
Zainab Hussein Mohsein; Ahmed Basil Abdulwahhab* ; Diana Abed Alkareem Noori
Production and Metallurgy Engineering Department, University of Technology, Baghdad, Iraq
Abstract
In machining operations, surface roughness (Ra) is an essential measure of product quality. It is determined by the cutting settings. The parameters that have been worked on are the Feed (F) (0.72, 0.88, 0.96, 1.12 mm/min), depth of cut (DOC) (0.5mm), and spindle speed (N) (545, 710, 1000, 1400 r.p.m). Three types of ferrous metals were employed in this study low-carbon steel St 3, medium-carbon steel St 45, and high-carbon steel Y8. According to the data, the optimal operating condition for obtaining the best surface roughness is 1.119 µm for low-carbon steel. St 3 from the product is by employing the following cutting settings for the cutter (feed 0.72 = mm/rev), (DOC= 0.5mm), and (machine speed =1400 rpm). But when using the cutting variables (feed 1.12 = mm/rev), (DOC = 0.5mm), and (machine speed = 545 rpm) for high-carbon steel Y8, gives the highest surface roughness is 4.999 µm . The experimental findings indicate that the surface roughness of turned components is considerably affected by cutting settings and machine equipment. According to the results of this study, increasing spindle speed lowered the Ra of the turned components, but rising feed increased the surface roughness. The value acquired by this approach will benefit other researchers for future work on tool vibrations, cutting forces, and so on.
Keywords
Surface Roughens; Cutting Condition; Feed Rate; Dry Turning; DOC
References
  • Karayel, “Prediction and control of surface roughness in CNC lathe using artificial neural network,” J. Mater. Process. Technol., vol. 209, no. 7, pp. 3125–3137, 2009. https://doi.org/10.1016/j.jmatprotec.2008.07.023.
  • Chen, R. Lin Peng, J. Zhou, R. M’Saoubi, D. Gustafsson, and J. Moverare, “Effect of machining parameters on cutting force and surface integrity when high-speed turning AD 730TM with PCBN tools,” Int. J. Adv. Manuf. Technol., vol. 100, no. 9–12, pp. 2601–2615, 2019. https://doi.org/10.1007/s00170-018-2792-1
  • Y. Kassab and Y. K. Khoshnaw, “The Effect of Cutting Tool Vibration on Surface Roughness of Workpiece in Dry Turning Operation,” Eng. Technol., vol. 25, no. 7, pp. 879–889, 2007.
  • Thamma, N. Pydisetti, M. Rajai, and H. Wang, “Comparison of regression models to study the effect of turning parameters on the surface roughness,” Int. J. Agil. Manuf., vol. 11, no. 1, pp. 1–9, 2009.
  • Mia et al., “Effect of time-controlled MQL pulsing on surface roughness in hard turning by statistical analysis and artificial neural network,” Int. J. Adv. Manuf. Technol., vol. 91, no. 9, pp. 3211–3223, 2017. https://doi.org/10.1007/s00170-016-9978-1
  • R. N. Vikas B. Magdum, “Experimental Study of the Effects of Machining Parameters on the Surface Roughness in the Turning Process,” vol. 4, no. 2, pp. 1–8, 2018. https://doi.org/10.22362/ijcert/2018/v5/i5/v5i502.
  • Kumar et al., “Influence of different grades of CBN inserts on cutting force and surface roughness of AISI H13 die tool steel during hard turning operation,” Materials (Basel)., vol. 12, no. 1, 2019.
https://doi.org/10.3390/ma12010177.

  • Sivalingam, Y. Zhao, R. Thulasiram, J. Sun, G. kai, and T. Nagamalai, “Machining Behaviour, surface integrity and tool wear analysis in environment-friendly turning of Inconel 718 alloy,” Measurement, vol. 174, p. 109028, 2021. https://doi.org/10.1016/j.measurement.2021.109028.
  • Padhan, A. Das, A. Santoshwar, T. R. Dharmendrabhai, and S. R. Das, “Sustainability Assessment and Machinability Investigation of Austenitic Stainless Steel in Finish Turning with Advanced Ultra-Hard SiAlON Ceramic Tool under Different Cutting Environments,” Silicon, vol. 13, no. 1, pp. 119–147, 2021. https://doi.org/10.1007/s12633-020-00409-1.
  • Ibrahim, “prediction of surface roughness in turning machine using taguchi method,” vol. 8, Jan. 2015.
  • Ahmed Al-Dolaimy, “Effect of Cutting Parameters on Surface Roughness in Turning Operations,” J. Eng. Sci., vol. 9, no. 4, pp. 442–449, 2016.
  • H. I. Haider M. Mohammad, “Effect Of Cutting Parameters On Surface Roughness And Cutting Tool Temperature In Turning AISI 1045 Steel,” vol. 8, no. 2, pp. 127–137, 2017.
  • F. Huayier, “Еxpeгimental Investigаtion of сutting cоnditions рarameters on surfаce roughness in aluminum alloys (AL-2024),” Al-Qadisiyah J. Eng. Sci., vol. 15, no. 3, pp. 142–147, 2022.
https://doi.org/10.30772/qjes.v15i3.826.

  • A. Sutar and A. J. Gujar, “Study the effect of machining parameters on surface roughness in CNC Milling of AISI 316L,” Int. J. Eng. Technol., vol. 10, no. 1, pp. 801–804, 2017.
  • Abdulridha, A. Helael, and A. Al-duroobi, “Prediction the Influence of Machining Parameters for CNC Turning of Aluminum Alloy Using RSM and ANN,” Eng. Technol. J., vol. 38, no. 6, pp. 887–895, 2020
 https://doi.org/10.30684/etj.v38i6A.705

  • Qin, “Micro-manufacturing engineering and technology,” Micro-Manufacturing Eng. Technol., 2015. https://doi.org/10.1016/C2013-0-19351-8.
  • H. M. Ghazali, A. Z. A. Mazlan, L. M. Wei, C. T. Tying, T. S. Sze, and N. I. M. Jamil, “Effect of Machining Parameters on the Surface Roughness for Different Type of Materials,” IOP Conf. Ser. Mater. Sci. Eng., vol. 530, no. 1, 2019. doi: 10.1088/1757-899X/530/1/012008.
  • M. Gurumurthy, J. Hindi, A. Hegde, S. Sharma, and A. Kini, “Effect of Machining Parameters on Tool Life and Surface Roughness of AISI 1040 Dual Phase Steel,” Mater. Res., vol. 25, 2022. doi: 10.1590/1980-5373-MR-2021-0351.
  • Zurita, V. Di-Graci, and M. Capace, “Effect of cutting parameters on surface roughness in turning of annealed AISI-1020 steel,” Rev. Fac. Ing., vol. 27, no. 47, pp. 111–118, 2018. doi: 10.19053/01211129.v27.n47.2018.7928.
  • Aghdeab, S., Abdulwahhab, A., & Mohsein, Z. , “Investigation study of electrical discharge machining parameters on material removal rate for AISI M2 material”. Al-Qadisiyah Journal for Engineering Sciences,2023, 16(1), 042-046. https://doi.org/10.30772/qjes.v16i1.832
Statistics
Article View: 705
PDF Download: 402


Journal Management System. Powered by iJournalPro.com