Majeed, S., K. Sayhood, E., S. Mohammed, N. (2023). Residual strength capacity of reinforced reactive powder concrete two-way slabs subjected to drop weight. , 16(1), 70-75. doi: 10.30772/qjes.v16i1.920
Sajjad Hameed Majeed; Eyad K. Sayhood; Nisreen S. Mohammed. "Residual strength capacity of reinforced reactive powder concrete two-way slabs subjected to drop weight". , 16, 1, 2023, 70-75. doi: 10.30772/qjes.v16i1.920
Majeed, S., K. Sayhood, E., S. Mohammed, N. (2023). 'Residual strength capacity of reinforced reactive powder concrete two-way slabs subjected to drop weight', , 16(1), pp. 70-75. doi: 10.30772/qjes.v16i1.920
Majeed, S., K. Sayhood, E., S. Mohammed, N. Residual strength capacity of reinforced reactive powder concrete two-way slabs subjected to drop weight. , 2023; 16(1): 70-75. doi: 10.30772/qjes.v16i1.920

Residual strength capacity of reinforced reactive powder concrete two-way slabs subjected to drop weight

Al-Qadisiyah Journal for Engineering Sciences
Volume 16, Issue 1, March 2023, Pages 70-75    PDF (511.73 K)
Document Type: Research Paper
DOI: 10.30772/qjes.v16i1.920
Authors
Sajjad Hameed Majeed* 1; Eyad K. Sayhood1; Nisreen S. Mohammed2
1Department of Civil Engineering, University of Technology, Baghdad
2Department of Civil Engineering, University of Technology, Baghdad, Iraq
Abstract
This paper presents an experimental investigation of the effect of the impact force on the residual strength capacity of simply supported reactive powder slabs. Eight specimens of reinforced reactive powder concrete slabs with dimensions of 500 x 500 mm and 70 mm in four categories were used. The influences of slab compressive strength (conventional concrete and reactive powder concrete), steel fiber proportion (1, 1.5, and 2%), percentage of reinforcement in the tension zone (ρ1=0.007, ρ2=0.011, ρ3=0.0179), and the number of impacts (two impacts, four impacts, and six impacts) were all investigated in this test. Investigations were carried out to ascertain each slab's residual response, including first cracking load, residual failure load, residual steel reinforcement strain, maximum central deflection, and crack pattern. The results showed that using reactive powder concrete instead of normal concrete increased the mechanical properties of concrete and resulted in a significant increase in failure load. In addition, the central deflection and strain increased. Increasing the reinforcement ratio increased the failure load while simultaneously decreasing the deflection due to the improvement in slab moment resistance. Furthermore, it was discovered through experiments that the addition of steel fiber to the mixture enhanced the slab’s post-cracking reactivity. The presence of steel fiber raised the slab strength resistance by 21.63% as the steel fiber ratio increased from 1% to 2%. This is because the addition of steel fiber increased the slab's tension resistance.
Keywords
Reinforced two; way slabs Reactive powder concrete Impact load Static load Drop weight
References
  • Kishi, O. Nakano, K.G. Matsuoka, and T. Ando, “Experimental Study on Ultimate Strength of Flexural-Failure-Type RC Beams under Impact Loading.,” Transactions of the 16th International Conference on Structural Mechanics in Reactor Technology. no. August, p. 1525, 2001.
  • Tachibana, H. Masuya, and S. Nakamura, “Performance-based design of reinforced concrete beams under impact.,” Natural Hazards and Earth System Science. vol. 10, no. 6, pp. 1069–1078, 2010.
  • -B. Zhao, W.-J. Yi, and S.K. Kunnath, “Shear Mechanisms in Reinforced Concrete Beams under Impact Loading.,” Journal of Structural Engineering. vol. 143, no. 9, p. 04017089, 2017.
  • Zhao, J. Qian, and P. Jia, “Peak Response Prediction for RC Beams under Impact Loading.,” Shock and Vibration. vol. 2019, p. 2019.
  • Fiengo Pérez, B. Luccioni, J.C. Vivas, F. Isla, and D. Sfer, “High strength fiber reinforced beams under impact load.,” International Journal of Impact Engineering. vol. 159, no. December 2020, p. 2022.
  • ASTM A 615/615M, “Standard Specification for Deformed and Plain Carbon Steel Bars for Concrete.,” no. March, pp. 1–6, 2004.
  • ASTM A 820/A 820M, “Standard Specification for Steel Fiber for FiberReinforced Concrete,” (2017).
  • 1984 I.Q.S No. 5, “Standard Specification for Portland Cement,” (1984).
  • BS 882, “Specification for aggregates from natural sources for,”.1992
  • Wille, A.E. Naaman, and G.J. Parra-Montesinos, “Ultra-High Performance Concrete with Compressive Strength Exceeding 150 MPa (22 ksi): A Simpler Way.,” ACI materials journal. vol. 108, no. 1, p. 2011.
  • G.A. AL-Khafaji, A.H.N. Al-Mamoori, and A.M.A. Aoun, “Improvement of Flexural Strength of Precast Concrete Spliced Girder Using Reactive Powder Concrete in Splice Region.,” Structures. vol. 14, no. March, pp. 197–208, 2018.
Statistics
Article View: 834
PDF Download: 169


Journal Management System. Powered by iJournalPro.com