Heat transfer augmentation by using different techniques in small scale channels: A review study

Abdul Kazem, Haider A.; Hamza, Naseer

doi:10.30772/qjes.2023.141640.1005

	Heat transfer augmentation by using different techniques in small scale channels: A review study
Al-Qadisiyah Journal for Engineering Sciences
Article 5, Volume 17, Issue 3, September 2024, Pages 239-249 PDF (446.74 K)
Document Type: Review Paper
DOI: 10.30772/qjes.2023.141640.1005
Authors
Haider A. Abdul kazem; Naseer Hamza^*
Mechanical Engineering Department, University of Al-Qadisiyah, Ad'Diwaniyah 58001, Iraq
Abstract
In this paper highlights the most significant recent developments in scientific study on Heat sinks are thermal management components made of materials with sufficient thermal conductivity qualities. Due to the increase in operating power and speed as well as the general reduction in system size, the issues of heat removal and temperature management have taken on increasing importance in these studies. Changing the geometry of extended surfaces, the material from which they were made, the working fluid that ran over them and or the dimension of the channel, are some of the subcategories in which studies have been conducted. The current review addresses the main recent findings in the forced convection heat transfer happened at laminar flow inside small scale diameters channels. The recent studies indicated a remarkable enhancement with the change of Re, D and internal geometry of channel. The configuration of flow passages also adopted as a different passive technique to enhance thermal fluid flow.
Keywords
Heat transfer; Forced convection; Enhancement; Channel; Thermal

References
Mohammed, H.M. and B.H. Abood, Influences the channel path on hydro-thermal performance in the serpentine mini-channel heat sink. Journal of Engineering and Sustainable Development (JEASD), 2022. 26(3). https://doi.org/10.31272/ jeasd.26.3.5 Liu, X. and J. Yu, Numerical study on performances of mini-channel heat sinks with non-uniform inlets. Applied Thermal Engineering,2016.93:p.856-864. https://doi.org/10.1016/j.applthermaleng.2015.09.032 Singh, V., H.C. Das, and P. Nemalipuri. Numerical analysis of heat transfer and fluid flow in mini-channel heat sink with interconnecting channels. in Advances in Mechanical Engineering: Select Proceedings of ICRIDME 2018. 2020. Springer. https://doi.org/10.1007/978-981-15-0124-1_88 Zhu, Q., et al., Characteristics of heat transfer and fluid flow in microchannel heat sinks with rectangular grooves and different shaped ribs. Alexandria Engineering Journal, 2020. 59(6): p. 4593-4609. https://doi.org/10.1016/j.aej.2020.08.014 Bi, C.T., G. H. Tao, W. Q., Heat transfer enhancement in mini-channel heat sinks with dimples and cylindrical grooves. Applied Thermal Engineering, 2013. 55(1): p. 121-132. https://doi.org/10.1016/j.applthermaleng.2013.03.007 Ho, C.J.G., Yu-Wei Yang, Tien-Fu Rashidi, Saman Yan, Wei-Mon, Numerical study on forced convection of water-based suspensions of nanoencapsulated PCM particles/Al2O3 nanoparticles in a mini-channel heat sink. International Journal of Heat and Mass Transfer, 2020. 157: p. 119965. https://doi.org/10.1016/j.ijheatmasstransfer.2020.119965 Muhammad, A.S., Deepak Wu, Jian, Numerical investigation of laminar flow and heat transfer in a liquid metal cooled mini-channel heat sink. International Journal of Heat and Mass Transfer, 2020. 150: p. 119265. https://doi.org/10.1016/j.ijheatmasstransfer.2019.119265 Nemati, H., M.A. Moghimi, and J.P. Meyer, Shape optimisation of wavy mini-channel heat sink. International Communications in Heat and Mass Transfer, 2021. 122: p. 105172. https://doi.org/10.1016/j.icheatmasstransfer.2021.105172 Kumar, S. and P.K.J.I.J.o.T.S. Singh, Effects of flow inlet angle on flow maldistribution and thermal performance of water cooled mini-channel heat sink. 2019. 138: p. 504-511. https://doi.org/10.1016/j.ijthermalsci.2019.01.014 Sarowar, M.T.J.C.I., Numerical analysis of a liquid metal cooled mini channel heat sink with five different ceramic substrates. 2021. 47(1): p. 214-225. https://doi.org/10.1016/j.ceramint.2020.08.124 Tikadar, A.O., Saad K. Paul, Titan C. Salman, Azzam S. Morshed, A. K. M. M. Khan, Jamil A., Parametric study on thermal and hydraulic characteristics of inter-connected parallel and counter flow mini-channel heat sink. Applied Thermal Engineering, 2019. 153: p. 15-28. https://doi.org/10.1016/j.applthermaleng.2019.02.007 Alfellag, M.A., H.E. Ahmed, and A.S. Kherbeet, Numerical simulation of hydrothermal performance of minichannel heat sink using inclined slotted plate-fins and triangular pins. Applied Thermal Engineering, 2020. 164: p. 114509. https://doi.org/10.1016/j.applthermaleng.2019.114509 Datta, A.S., Vivek Sanyal, Dipankar Das, Pritam, A conjugate heat transfer analysis of performance for rectangular microchannel with trapezoidal cavities and ribs. International Journal of Thermal Sciences, 2019. 138: p. 425-446. https://doi.org/10.1016/j.ijthermalsci.2018.12.020 Hung, T.-C., et al., Thermal performance of porous microchannel heat sink: Effects of enlarging channel outlet. 2013. 48: p. 86-92. https://doi.org/10.1016/j.icheatmasstransfer.2013.08.001 Saadoon, Z.H.A., Farooq H. Sheikholeslami, M., Numerical investigation of heat transfer enhancement using (Fe3O4 and Ag-H2O) nanofluids in (converge-diverge) mini-channel heat sinks. Materials Today: Proceedings, 2021. https://doi.org/10.1016/j.matpr.2021.07.091 Xiao, H., Z. Liu, and W.J.A.T.E. Liu, Conjugate heat transfer enhancement in the mini-channel heat sink by realizing the optimized flow pattern. 2021. 182: p. 116131. https://doi.org/10.1016/j.applthermaleng.2020.116131 Moradikazerouni, A.A., Masoud Alsarraf, Jalal Mahian, Omid Wongwises, Somchai Tran, Minh-Duc, Comparison of the effect of five different entrance channel shapes of a micro-channel heat sink in forced convection with application to cooling a supercomputer circuit board. Applied Thermal Engineering, 2019. 150: p. 1078-1089. https://doi.org/10.1016/j.applthermaleng.2019.01.051 Leng, C.W., Xiao-Dong Wang, Tian-Hu, An improved design of double-layered microchannel heat sink with truncated top channels. Applied Thermal Engineering, 2015. 79: p. 54-62. https://doi.org/10.1016/j.applthermaleng.2015.01.015 Xia, G.D.J., Y. T Li, Y. F. Ma, D. D. Cai, B., Numerical simulation and multiobjective optimization of a microchannel heat sink with arc-shaped grooves and ribs. Numerical Heat Transfer, Part A: Applications, 2016. 70(9): p. 1041-1055. https://doi.org/10.1080/10407782.2016.1230394 Ghahremannezhad, A., K.J.I.J.o.H. Vafai, and M. Transfer, Thermal and hydraulic performance enhancement of microchannel heat sinks utilizing porous substrates. 2018. 122: p. 1313-1326. https://doi.org/10.1016/j.ijheatmasstransfer.2018.02.024 Wong, K.-C., J.-H.J.I.c.i.h. Lee, and m. transfer, Investigation of thermal performance of microchannel heat sink with triangular ribs in the transverse microchambers. 2015. 65: p. 103-110. https://doi.org/10.1016/j.icheatmasstransfer.2015.04.011 Lin, L.Z., Jun Lu, Gui Wang, Xiao-Dong Yan, Wei-Mon, Heat transfer enhancement in microchannel heat sink by wavy channel with changing wavelength/amplitude. International Journal of Thermal Sciences, 2017. 118: p. 423-434. https://doi.org/10.1016/j.ijthermalsci.2017.05.013 Shamsi, M.R.A., Omid Ali Marzban, Ali and D.M. Toghraie, Ramin, Increasing heat transfer of non-Newtonian nanofluid in rectangular microchannel with triangular ribs. Physica E: Low-dimensional Systems and Nanostructures, 2017. 93: p. https://doi.org/10.1016/j.physe.2017.06.015 Wang, T.-H.W., Hao-Chi Meng, Jing-Hui Yan, Wei-Mon, Optimization of a double-layered microchannel heat sink with semi-porous-ribs by multi-objective genetic algorithm. International Journal of Heat and Mass Transfer, 2020. 149: p. 119217. https://doi.org/10.1016/j.ijheatmasstransfer.2019.119217 Shi, X.L., Shan Mu, Yingjie Yin, Bangtao, Geometry parameters optimization for a microchannel heat sink with secondary flow channel. International Communications in Heat and Mass Transfer, 2019. 104: p. 89-100. https://doi.org/10.1016/j.icheatmasstransfer.2019.03.009 Shi, Z., T.J.E.C. Dong, and Management, Entropy generation and optimization of laminar convective heat transfer and fluid flow in a microchannel with staggered arrays of pin fin structure with tip clearance. 2015. 94: p. 493-504. https://doi.org/10.1016/j.enconman.2015.02.009 Jajja, S.A.A., Wajahat Ali, Hafiz Muhammad Ali, Aysha Maryam, Water cooled minichannel heat sinks for microprocessor cooling: Effect of fin spacing. Applied Thermal Engineering, 2014. 64(1): p. 76-82. https://doi.org/10.1016/j.applthermaleng.2013.12.007 Lim, K., J.J.E.C. Lee, and Management, Experimental study on single-phase convective heat transfer of interlocking double-layer counterflow mini-channel heat sink. 2021. 243: p. 114415. https://doi.org/10.1016/j.enconman.2021.114415 Kumar, V., J. Sarkar, and W.-M.J.I.J.o.T.S. Yan, Thermal-hydraulic behavior of lotus like structured rGO-ZnO composite dispersed hybrid nanofluid in mini channel heat sink. 2021. 164: p. 106886. https://doi.org/10.1016/j.ijthermalsci.2021.106886 Mohammadi, M.T., Amin Passandideh-Fard, Mohammad Sardarabadi, Mohammad, Electronic chipset thermal management using a nanofluid-based mini-channel heat sink: An experimental study. International Communications in Heat and Mass Transfer, 2020. 118: p. 104836. https://doi.org/10.1016/j.icheatmasstransfer.2020.104836 Ho, C.J., et al., Cooling performance of mini-channel heat sink with water-based nano-PCM emulsion-An experimental study. International Journal of Thermal Sciences, 2021. 164: p. 106903. https://doi.org/10.1016/j.ijthermalsci.2021.106903 Halelfadl, S.A., Ahmed Mohammed Mohd-Ghazali, Normah Maré, Thierry Estellé, Patrice Ahmad, Robiah, Optimization of thermal performances and pressure drop of rectangular microchannel heat sink using aqueous carbon nanotubes based nanofluid. Applied Thermal Engineering, 2014. 62(2): p. 492-499. https://doi.org/10.1016/j.applthermaleng.2013.08.005 Jaffal, H.M.F., Basim Hussain, Ammar A. Hasan, Ala, Effect of the fluid flow fragmentation on the hydrothermal performance enhancement of a serpentine mini-channel heat sink. Case Studies in Thermal Engineering, 2021. 24: p. 100866. https://doi.org/10.1016/j.csite.2021.100866 Khalifa, M.A. and H.M.J.A.T.E. Jaffal, Effects of channel configuration on hydrothermal performance of the cylindrical mini-channel heat sinks. 2019. 148: p. 1107-1130. https://doi.org/10.1016/j.applthermaleng.2018.11.101 Ghasemi, S.E., A.A. Ranjbar, and M.J. Hosseini, Experimental and numerical investigation of circular minichannel heat sinks with various hydraulic diameter for electronic cooling application. Microelectronics Reliability, 2017. 73: p. 97-105. https://doi.org/10.1016/j.microrel.2017.04.028 Imran, A.A., et al., Numerical and experimental investigation of heat transfer in liquid cooling serpentine mini-channel heat sink with different new configuration models. 2018. 6: p. 128-139. https://doi.org/10.1016/j.tsep.2018.03.011 Kumar, P.J.I.J.o.T.S., Numerical investigation of fluid flow and heat transfer in trapezoidal microchannel with groove structure. 2019. 136: p. 33-43. https://doi.org/10.1016/j.ijthermalsci.2018.10.006 Abdulqadur, A.A., H.M. Jaffal, and D.S.J.I.J.o.T.S. Khudhur, Performance optimiation of a cylindrical mini-channel heat sink using hybrid straight–wavy channel. 2019. 146: p. 106111. https://doi.org/10.1016/j.ijthermalsci.2019.106111 Tikadar, A.P., Titan C. Oudah, Saad K. Abdulrazzaq, Nabeel M. Salman, Azzam S. Khan, Jamil A., enhancing thermal-hydraulic performance of counter flow mini-channel heat sinks utilizing secondary flow: Numerical study with experimental validation. International Communications in Heat and Mass Transfer, 2020. 111: p. 104447. https://doi.org/10.1016/j.icheatmasstransfer.2019.104447 Chamanroy, Z. and M. Khoshvaght-Aliabadi, Analysis of straight and wavy miniature heat sinks equipped with straight and wavy pin-fins. International Journal of Thermal Sciences, 2019. 146: p. 106071. https://doi.org/10.1016/j.ijthermalsci.2019.106071 Liu, X., et al., Effect of pore structure on heat transfer performance of lotus-type porous copper heat sink. International Journal of Heat and Mass Transfer, 2019. 144: p. 118641. https://doi.org/10.1016/j.ijheatmasstransfer.2019.118641 Tsai, T.-H. and R. Chein, Simple model for predicting microchannel heat sink performance and optimization. Heat and Mass Transfer, 2012. 48(5): p. 789-798. https://doi.org/10.1007/s00231-011-0933-2 Mat Tokit, E., M.Z. Yusoff, and H.A. Mohammed, Generality of Brownian motion velocity of two-phase approach in interrupted microchannel heat sink. International Communications in Heat and Mass Transfer, 2013. 49: p. 128-135. https://doi.org/10.1016/j.icheatmasstransfer.2013.10.005 Yang, Y.-T.T., Kuo-Teng Wang, Yi-Hsien Lin, Shih-Han, Numerical study of microchannel heat sink performance using nanofluids. International Communications in Heat and Mass Transfer, 2014. 57: p. 27-35. https://doi.org/10.1016/j.icheatmasstransfer.2014.07.006 Xie, G., H. Shen, and C.-C. Wang, Parametric study on thermal performance of microchannel heat sinks with internal vertical Y-shaped bifurcations. International Journal of Heat and Mass Transfer, 2015. 90: p. 948-958. https://doi.org/10.1016/j.ijheatmasstransfer.2015.07.034 Dewan, A. and P. Srivastava, A review of heat transfer enhancement through flow disruption in a microchannel. Journal of Thermal Science, 2015. 24: p. 203-214. https://doi.org/10.1007/s11630-015-0775-1 Shi, Z. and T. Dong, Entropy generation and optimization of laminar convective heat transfer and fluid flow in a microchannel with staggered arrays of pin fin structure with tip clearance. Energy Conversion and Management, 2015. 94: p. 493-504. https://doi.org/10.1016/j.enconman.2015.02.009 Xu, M.L., Hui Gong, Liangn Chai, John C. Duan, Xinyue, Parametric numerical study of the flow and heat transfer in microchannel with dimples. International Communications in Heat and Mass Transfer, 2016. 76: p. 348-357. https://doi.org/10.1016/j.icheatmasstransfer.2016.06.002 Anbumeenakshi, C.T., M. R., On the effectiveness of a nanofluid cooled microchannel heat sink under non-uniform heating condition. Applied Thermal Engineering, 2017. 113: p. 1437-1443. https://doi.org/10.1016/j.applthermaleng.2016.11.144 Manay, E. and B. Sahin, Heat Transfer and Pressure Drop of Nanofluids in a Microchannel Heat Sink. Heat Transfer Engineering, 2017. 38(5): p. 510-522. https://doi.org/10.1080/10407782.2016.1195162 Sidik, N.A.C., et al., An overview of passive techniques for heat transfer augmentation in microchannel heat sink. International Communications in Heat and Mass Transfer, 2017. 88: p. 74-83. https://doi.org/10.1016/j.icheatmasstransfer.2017.08.009 Makam, J.S. and N.B. Totla, Heat Transfer Characteristics of Water Cooled Minichannel Heat Sink Using Different Fluid Flow Geometries. IOP Conference Series: Materials Science and Engineering, 2020. 998(1): p. 012018. DOI1088/1757-899X/998/1/012018 Gunnasegaran, P., et al., The effect of geometrical parameters on heat transfer characteristics of microchannels heat sink with different shapes. International Communications in Heat and Mass Transfer, 2010. 37(8): p. 1078-1086. https://doi.org/10.1016/j.icheatmasstransfer.2010.06.014 Wu, H.Y. and P. Cheng, Friction factors in smooth trapezoidal silicon microchannels with different aspect ratios. International Journal of Heat and Mass Transfer, 2003. 46(14): p. 2519-2525. https://doi.org/10.1016/S0017-9310(03)00106-6 Wang, X.-Q., A.S. Mujumdar, and C. Yap, Thermal characteristics of tree-shaped microchannel nets for cooling of a rectangular heat sink. International Journal of Thermal Sciences, 2006. 45(11): p. 1103-1112. https://doi.org/10.1016/j.ijthermalsci.2006.01.010
Statistics Article View: 5,403 PDF Download: 218