Sultan, B., Abbass, M., Yagoob, J., Guo, Y. (2024). Experimental and optimization study of powder metallurgy process parameters of magnesium base AZ31 alloy using taguchi method. , 42(6), 687-698. doi: 10.30684/etj.2023.142510.1539
Basma F. Sultan; Muna K. Abbass; Jawdat A. Yagoob; Yang Y. Guo. "Experimental and optimization study of powder metallurgy process parameters of magnesium base AZ31 alloy using taguchi method". , 42, 6, 2024, 687-698. doi: 10.30684/etj.2023.142510.1539
Sultan, B., Abbass, M., Yagoob, J., Guo, Y. (2024). 'Experimental and optimization study of powder metallurgy process parameters of magnesium base AZ31 alloy using taguchi method', , 42(6), pp. 687-698. doi: 10.30684/etj.2023.142510.1539
Sultan, B., Abbass, M., Yagoob, J., Guo, Y. Experimental and optimization study of powder metallurgy process parameters of magnesium base AZ31 alloy using taguchi method. , 2024; 42(6): 687-698. doi: 10.30684/etj.2023.142510.1539

Experimental and optimization study of powder metallurgy process parameters of magnesium base AZ31 alloy using taguchi method

Engineering and Technology Journal
Volume 42, Issue 6, June 2024, Pages 687-698    PDF (1.1 M)
Document Type: Research Paper
DOI: 10.30684/etj.2023.142510.1539
Authors
Basma F. Sultan* 1; Muna K. Abbass1; Jawdat A. Yagoob2; Yang Y. Guo3
1Production Engineering and Metallurgy Dept., University of Technology-Iraq, Alsina’a street, 10066 Baghdad, Iraq.
2Engineering Technical Collage Kirkuk Northern Technical University, Kirkuk-Iraq
3Northwest Institute of Non-ferrous Metal Research, China.
Abstract
Powder metallurgy (PM) is a highly effective re-processing method mostly used for magnesium-base alloys, especially in high-performance Mg alloys. In the present work, the experimental and optimization of PM process parameters, including compaction pressure, sintering temperature, and sintering time, for AZ31 magnesium alloy have been investigated using Taguchi Design of Experiment (DOE) and ANOVA method. The regression equation for obtaining density, porosity, and hardness of AZ31 Mg alloy has been formulated and experimentally validated. Three parameters are dependent in the current work, 450, 550, and 600 MPa compaction pressure, 455, 520, and 585ºC sintering temperature, and 30, 60, and 90 min sintering time. It was found that the factors determined beyond analyzing the main effect plots for means is an amalgamation of a compaction pressure (600 MPa), a temperature (585ºC) of sintering, and a time (60 min) of sintering. The optimal density, porosity, and hardness values determined from the regression equations are 1.82 g/cm3, 3.4%, and 72.10 HV, correspondingly. The experimental density, porosity, and hardness values for the samples treated at the optimum factors are 1.73 g/cm3, 2.2%, and 74.51 HV. The percentage error between the investigational outcomes and the outcomes resulted is < 3% for density, porosity, and hardness. The analysis ANOVA also found that the compaction pressure is the highly effective factor in the density, porosity, and hardness of sintered samples, followed by the same effective sintering temperature and time.

Highlights
  • Taguchi Design and ANOVA analysis were used to optimize powder metallurgy parameters.
  • AZ31 alloy was fabricated using the powder metallurgy technique.
  • Compaction pressure was the most impactful factor for density, porosity, and hardness at optimal settings.
Keywords
AZ31 magnesium alloy; Taguchi design; ANOVA analysis; Powder metallurgy; Microstructure
References
  1. Cai, F. Guo, Study on Microstructure and Strengthening Mechanism of AZ91-YMagnesium alloy, Mater. Res. Express, 5 ( 2018) 36-50 . https://doi.org/10.1088/2053-1591/aab0b7
  2. Ghasali, M. Alizadeh, M.Niazmand, and T.Ebadzadeh, Fabrication of Magnesium-Boron Carbide Metal Matrix Composite by Powder Metallurgy Route: Comparison between Microwave and Spark Plasma Sintering, J. Alloys Compd., 697 (2016) 200-207. https://doi.org/10.1016/j.jallcom.2016.12.146
  3. S.Goh, J. Wei , L.C.Lee,M.Gupta, Development of Novel Carbon Nanotube Reinforced Magnesium Nanocomposites using the Powder Metallurgy Technique, Nanotechnology, 17 (2006) 7-12. https://doi.org/10.1088/0957-4484/17/1/002
  4. F. Guleryuz , S. Ozan, D. Uzunsoy, R. Ipek , An Investigation of The Microstructure and Mechanical Properties of B4C Reinforced PM Magnesium Matrix Composites, Powder Metall. Met. Ceram., 51 (2012) 456-462. https://doi.org/10.1007/s11106-012-9455-9
  5. Akcamlı , B. Senyurt , Fabrication and Characterization of In-situ Al3Ni Intermetallic and CeO2 Particulate-Reinforced Aluminum Matrix Composites, Ceram. Int., 47 (2021) 197-206. https://doi.org/10.1016/j.ceramint.2021.04.122
  6. Dey, K.M.Pandey , Magnesium Metal Matrix Composites - A Review, Rev. Adv. Mater.Sci., 42 (2015) 58-67.
  7. Ali , M.A.Husseien and N.AL-Aqeeli ,Magnesium –based composites alloys for medical applications :A review of mechanical and corrosion properties, J. Alloys Compd., 792 (2019) 162-1190.
  8. peter, A. Man and G. Dias ,Magnesium and it Alloys as orthopedic biomaterials, Elsever, 27 (2006) 1728-1734.
  9. Burke, D. Fancelli and G. J. Kipouros, Investigation of the Sintering , Metals in Transport Applications, 48 (2009) 123-132. http://dx.doi.org/10.1179/cmq.2009.48.2.123
  10. Blawert, N. Hort, K.U. Kainer, Automotive applications of Magnesium and its alloys, Trans. Indian Inst. Met.,57 ( 2004) 397-408.
  11. Kumar, A. Bharti, S.M. Azam, N. Kumar, H. Tripathi‏, Investigations of Mechanical Properties of Copper Matrix Hybrid Composite, Adv. Mech. Eng., 46 (2020).671-676. https://doi.org/10.1007/978-981-15-0124-1_60
  12. H.Y. Wang, Q.C. Jiang, Y. Wang, B.X. Ma, F. Zhao, Fabrication of TiB2 Particulate Reinforced Magnesium Matrix Composites by Powder Metallurgy, Mater. Lett., 58 (2004) 3509-3513. https://doi.org/10.1016/j.matlet.2004.04.038
  13. K. Abbass, J. A. yagoob, Effect of a-Al2o3 Nanoparticles Addition On Some Properties Of Cocrmo Alloy Fabricated By Powder Metallurgy Route, Iraqi J. Mech. Mater. Eng., 20 (2020) 47-62.
  14. Guo, H. Xin, Z. Zhang, X. Zhang, F. Ye‏, Microstructure Modification of Y2O3 Stabilized ZrO2 Thermal Barrier Coating by Laser Lazing and Effect on the Hot Corrosion Resistance, J. Adv. Ceram., 9 (2020) 232-242. https://doi.org/10.1007/s40145-020-0363-z
  15. J. Durai, M. Sivapragash, M.E .Sahayaraj, Effect of Sintering Temperature on Mechanical Properties of Mg-Zr Alloy, Int. J. Mech. Prod. Eng. Res. Dev., 7 (2017) 117-122.
  16. Ma, P. Jin , X. Feng L.i Jia, Effect of Sintering Temperature on Microstructure and Mechanical Properties of ZK60 magnesium alloys,Mater.l Res. express., 9 (2022) 016514.https://doi.org/10.1088/2053-1591.
  17. P Burke, G.J. Kipouros, Development of Magnesium Powder Metallurgy AZ31 Alloy Using Commercially Available Powders, High Temp. Mater. Proc., 30 (2011) 51–61.https://doi.org/10.1515/htmp.2011.007
  18. A. Alrebdi, R. Gopinathan, P. Sunagar, R.T. Prabu, R. Kivade, M.Z .Gous, A. Alodhayb, Optimization on Powder Metallurgy Process Parameters on Nano BoronCarbide and Micron Titanium Carbide Particles Reinforced AA 4015 Composites by Taguchi Technique, J. Nanomater., 2022 (2022) 1-9 . https://doi.org/10.1155/2022/3577793
  19. Kumar, A. Bharti , Optimization of powder metallurgy process parameters to recycle AZ31 magnesium alloy , Material physic N Kumar, A Bharti al mechanics , 47 (2021) 968-977. http://dx.doi.org/10.18149/MPM.4762021_15
  20. Magdum, P. Chinnaiyan‏, Experimental Investigation and Optimization of AZ31 Mg Alloy during Warm Incremental Sheet Forming to Study Fracture and Forming Behavior, Coatings, 68 (2023) 2-19. https://doi.org/10.3390/coatings13010068
  21. Zhuanxin, Chemical Composition of Magnesium alloy (%) ASTM standard, and Mechanical Properties of Magnesium alloys, All kind metal material and CNC machining part and rapid prototype manufacture, Page 1
  22. K. Abbass, B.F. Sultan‏, Effect of Al2O3 Nano-particles on Corrosion Behavior of Aluminum alloy (Al-4.5%Cu-1.5 Mg) Fabricated by Powder Metallurgy ,Journal Engineering Structure and Technologies ,11(2019) 1-7.
  23. A. Yagoob, M.K. Abbass‏, Characterization of Cobalt Based CoCrMo Alloy Fabricated by Powder Metallurgy Route, 2nd Int. Conf. Eng. Technol. Sci. Al-Kitab University, 2018, 1-5. https://doi.org/10.1109/ICETS.2018.8724615
  24. K. Abbass, B.F. Sultan‏, Effect Sintering Temperature on Physical Properties and Corrosion Behavior of Compact (Al-4.5wt% Cu-1.5 wt% Mg ) Alloy, Iraqi J. Mech. Mater. Eng., 17 (2017) 394-407.
  25. Marya, L.G .Hector, R. Verma, W. Tong, Microstructural effects of AZ31 magnesium alloy on its tensile deformation and failure behaviors Mater. Sci. Eng. A, 418 (2006) 341-356. https://doi.org/10.1016/j.msea.2005.12.003
  26. Kumar, P.M. Pandey,Development of my Mg based biomaterials with improved mechanical and degradation properties using powder metallurgy , J. Magnes. Alloy., 8 (2020) 883-898. https://doi.org/10.1016/j.jma.2020.02.011
Statistics
Article View: 316
PDF Download: 450


Journal Management System. Powered by iJournalPro.com