Al-Chlaihawi, K., Hasan, M., Kaied, A. (2024). Computational insights into the thermal performance enhancement of solar air heater channel through metal foam integration. , 42(7), 841-868. doi: 10.30684/etj.2024.145706.1660
Kadhim Al-Chlaihawi; Moayed R. Hasan; Ali L. Kaied. "Computational insights into the thermal performance enhancement of solar air heater channel through metal foam integration". , 42, 7, 2024, 841-868. doi: 10.30684/etj.2024.145706.1660
Al-Chlaihawi, K., Hasan, M., Kaied, A. (2024). 'Computational insights into the thermal performance enhancement of solar air heater channel through metal foam integration', , 42(7), pp. 841-868. doi: 10.30684/etj.2024.145706.1660
Al-Chlaihawi, K., Hasan, M., Kaied, A. Computational insights into the thermal performance enhancement of solar air heater channel through metal foam integration. , 2024; 42(7): 841-868. doi: 10.30684/etj.2024.145706.1660

Computational insights into the thermal performance enhancement of solar air heater channel through metal foam integration

Engineering and Technology Journal
Volume 42, Issue 7, July 2024, Pages 841-868    PDF (3.17 M)
Document Type: Research Paper
DOI: 10.30684/etj.2024.145706.1660
Authors
Kadhim Al-Chlaihawi* 1; Moayed R. Hasan2; Ali L. Kaied2
1Department of Mechanical Engineering, University of Al-Qadisiyah, Al Diwaniyah, Al-Qadisiyah, 58001, Iraq .
2Mechanical Engineering Dept., University of Technology-Iraq, Alsina’a street, 10066 Baghdad, Iraq.
Abstract
The two-dimensional numerical simulations focused on fluid flow and heat transfer within a solar air heater (SAH) channel incorporating copper metal foam with a porosity of 90% were carried out in this study. The Local Thermal Non-equilibrium (LTNE) and Darcy-Extended Forchheimer (DEF) models were employed to predict fluid and thermal transport in the partially porous SAH channel. In the free flow zone, the  turbulence model was utilized. The thermal and thermo-hydraulic performances of SAH were examined concerning several factors, including pore density ( ), Reynolds number ( ), and dimensionless foam height ( ). The results demonstrate that inserting a porous substrate into the SAH can substantially increase heat transmission. This enhancement ranges from 4.4 to 18.04 times compared to an empty duct for  at . Moreover, increased porous layer height and pore density lead to a corresponding increase in pressure drop. Evaluating both the improvement in heat transmission and the associated pressure penalty, the case with ,  and  demonstrate superior overall performance, boasting a higher Thermal Performance Factor ( ) of 2.82 when compared to an empty channel. This work presents significant findings on optimizing metal foam applications in SAH systems, offering new insights into the field.

Highlights
  • Fluid flow and heat transfer in an SAH channel with metal foam were simulated
  • The LTNE and DEF models were used.
  • The thermo-hydraulic performance of SAH was analyzed, considering several key factors.
  • Compared to the empty SAH duct, Nu rises 9-10.6 times and friction factor by 53.5-56.6 times.
  • TPF varies from 2.33 to 2.82 at Hf =0.6 and ω=10 PPI.
Keywords
metal foam; local thermal non-equilibrium; model (LTNE) forced convection; TPF; SAH
References
  1. F. Xia, et al., Enhanced thermal performance of a flat-plate solar collector inserted with porous media: A numerical simulation study, Therm. Sci. Eng. Prog., 44 (2023) 102063. https://doi.org/10.1016/j.tsep.2023.102063
  2. Liu, et al., Game theory-based renewable multi-energy system design and subsidy strategy optimization, Adv. Appl. Energy, 2 (2021) 100024. https://doi.org/10.1016/j.adapen.2021.100024
  3. Yan, J., Energy systems in transition: challenges and opportunities, Adv. Appl. Energy, 1 (2020) 100005. http://dx.doi.org/10.1016/j.adapen.2020.100005
  4. A. Sakhaei, and M.S. Valipour, Performance enhancement analysis of The flat plate collectors: A comprehensive review, Renewable Sustainable Energy Rev., 102 (2019) 186-204. https://doi.org/10.1016/j.rser.2018.11.014
  5. Choudhury, P.K. and D.C. Baruah, Solar air heater for residential space heating, Energy Ecol. Environ., 2 (2017) 387-403. https://doi.org/10.1007/s40974-017-0077-4
  6. Saxena, et al., Experimental studies of latent heat storage based solar air heater for space heating: A comparative analysis, J. Build. Eng., 69 (2023) 106282. https://doi.org/10.1016/j.jobe.2023.106282
  7. Al-damook, and W.H. Khalil, Experimental evaluation of an unglazed solar air collector for building space heating in Iraq, Renewable Energy, 112 (2017) 498-509. https://doi.org/10.1016/j.renene.2017.05.051
  8. Kumara, et al., Performance improvement of a solar desalination system assisted with solar air heater: An experimental approach, J. Indian Chem. Soc., 79 (2020) 1967-1972.
  9. García-Valladares, et al., Solar thermal drying plant for agricultural products. Part 1: Direct air heating system. Renewable Energy, 148 (2020) 1302-1320. https://doi.org/10.1016/j.renene.2019.10.069
  10. Lingayat, R. Zachariah, and A. Modi, Current status and prospect of integrating solar air heating systems for drying in various sectors and industries, Sustainable Energy Technol. Assess., 52 (2022) 102274. https://doi.org/10.1016/j.seta.2022.102274
  11. Gorjian, et al., A review on recent advancements in performance enhancement techniques for low-temperature solar collectors, Energy Convers. Manage., 222 (2020) 113246. https://doi.org/10.1016/j.enconman.2020.113246
  12. K. Al‐Chlaihawi, M.R. Hasan, and A.L. Ekaid, Compound passive heat transfer augmentation techniques: A comprehensive review, Heat Transfer.53 (2023) 363-421. https://doi.org/10.1002/htj.22955
  13. Prakash, and R.P. Saini, Use of artificial roughness for performance enhancement of solar air heaters—a review. Int. J. Green Energy, 16 (2019) 551-572. https://doi.org/10.1080/15435075.2019.1598418
  14. K. Al‐Chlaih awi, K.K.I., M.R. Hasan, and A.L. Ekaid, Thermohydraulic performance assessment of a solar air heater with equilateral‐triangular, trapezoidal, and square sectional ribs on the absorber plate: A comparative study, Heat Transfer, 53 (2023) 441-471. https://doi.org/10.1002/htj.22958
  15. K. Al-Chlaihawi, B.H. Alyas, and A.A. Badr, CFD Based Numerical Performance Assessment of a Solar Air Heater Duct Roughened by Transverse-Trapezoidal Sectioned Ribs, Int. J. Heat Technol., 41 (2023) 1273-1281, https://doi.org/10.18280/ijht.410517
  16. H. Abu-Hamdeh, R.A. Alsulami, and R.I. Hatamleh, A case study in the field of building sustainability energy: Performance enhancement of solar air heater equipped with PCM: A trade-off between energy consumption and absorbed energy, J. Build. Eng., 48 (2022) 103903. https://doi.org/10.1016/j.jobe.2021.103903
  17. Assadeg, et al., Energetic and exergetic analysis of a new double pass solar air collector with fins and phase change material, Sol. Energy, 226 (2021) 260-271. https://doi.org/10.1016/j.solener.2021.08.056
  18. Kumar, S. Kumar Verma, and V. Kumar Sharma, Performance enhancement analysis of triangular solar air heater coated with nanomaterial embedded in black paint, Mater. Today: Proc., 26 (2020) 2528-2532. https://doi.org/10.1016/j.matpr.2020.02.538
  19. Kumar, and P. Chand, Performance enhancement of solar air heater using herringbone corrugated fins, Energy, 127 (2017) 271-279. https://doi.org/10.1016/j.energy.2017.03.128
  20. C. Ifrim, and O.V. Grosu. Review of thermal performance enhancement of Solar Air Heater using baffles on absorber plate, International Conference on Development and Application Systems (DAS). 2022. IEEE. https://doi.org/10.1109/DAS54948.2022.9786129
  21. Chand, P. Chand, and H. K. Ghritlahre, Thermal performance enhancement of solar air heater using louvered fins collector, Sol. Energy, 239 (2022) 10-24. https://doi.org/10.1016/j.solener.2022.04.046
  22. Zhu, and Y. Xuan, Pore scale numerical simulation of heat transfer and flow in porous volumetric solar receivers, Appl. Therm. Eng., 120 (2017) 150-159. https://doi.org/10.1016/j.applthermaleng.2017.03.141
  23. F. Jouybari, and T.S. Lundström, Performance improvement of a solar air heater by covering the absorber plate with a thin porous material, Energy, 190 (2020) 116437. https://doi.org/10.1016/j.energy.2019.116437
  24. Chen, M. Gu, and D. Peng, Heat transfer performance analysis of a solar flat-plate collector with an integrated metal foam porous structure filled with paraffin, Appl. Therm. Eng., 30 (2010) 1967-1973. https://doi.org/10.1016/j.applthermaleng.2010.04.031
  25. Rashidi, M. Bovand, and J.A. Esfahani, Heat transfer enhancement and pressure drop penalty in porous solar heat exchangers: A sensitivity analysis, Energy Convers. Manage., 103 (2015) 726-738. https://doi.org/10.1016/j.enconman.2015.07.019
  26. Bovand, S. Rashidi, and J.A. Esfahani, Heat transfer enhancement and pressure drop penalty in porous solar heaters: Numerical simulations, Sol. Energy, 123 (2016) 145-159. https://doi.org/10.1016/j.solener.2015.10.054
  27. T. Jamal-Abad, S. Saedodin, and M. Aminy, Heat transfer in concentrated solar air-heaters filled with a porous medium with radiation effects: A perturbation solution, Renewable Energy, 91 (2016) 147-154. https://doi.org/10.1016/j.renene.2016.01.050
  28. J. Jouybari, et al., Experimental investigation of thermal performance and entropy generation of a flat-plate solar collector filled with porous medial, Appl. Therm. Eng., 127 (2017) 1506-1517. https://doi.org/10.1016/j.applthermaleng.2017.08.170
  29. Saedodin, et al., Performance evaluation of a flat-plate solar collector filled with porous metal foam: Experimental and numerical analysis, Energy Convers. Manage., 153 (2017) 278-287. https://doi.org/10.1016/j.enconman.2017.09.072
  30. J. Jouybari, et al., Effects of porous material and nanoparticles on the thermal performance of a flat plate solar collector: An experimental study, Renewable Energy, 114 (2017) 1407-1418. https://doi.org/10.1016/j.renene.2017.07.008
  31. J. Jouybari, et al., Analytical investigation of forced convection heat transfer in a flat-plate solar collector filled with a porous medium by considering radiation effect, J. Porous Media, 21 (2018). http://dx.doi.org/10.1615/JPorMedia.2018028768
  32. Valizade, M., M. Heyhat, and M. Maerefat, Experimental study of the thermal behavior of direct absorption parabolic trough collector by applying copper metal foam as volumetric solar absorption, Renewable Energy, 145 (2020) 261-269. https://doi.org/10.1016/j.renene.2019.05.112
  33. Anirudh, and S. Dhinakaran, Performance improvement of a flat-plate solar collector by inserting intermittent porous blocks, Renewable Energy, 145 (2020) 428-441. https://doi.org/10.1016/j.renene.2019.06.015
  34. Anirudh, and S. Dhinakaran, Numerical analysis of the performance improvement of a flat-plate solar collector using conjugated porous blocks, Renewable Energy, 172 (2021) 382-391. https://doi.org/10.1016/j.renene.2021.02.145
  35. Diganjit, N. Gnanasekaran, and M. Mobedi, Numerical Study for Enhancement of Heat Transfer Using Discrete Metal Foam with Varying Thickness and Porosity in Solar Air Heater by LTNE Method, Energies, 15 (2022) 8952. https://doi.org/10.3390/en15238952
  36. G. Fadhala, E.M. Fayyadh, and A.F. Mohammed, Experimental investigation on the thermal-hydraulic performance of channel with gradient metal foam baffles, FME Transactions, 51 (2023) 14-22. https://doi.org/10.5937/fme2301014F
  37. Fu, et al., A novel structure design and numerical analysis of porous media-assisted enhanced thermal performance of flat-plate solar collector, Therm. Sci. Eng. Prog., 40 (2023) 101777. https://doi.org/10.1016/j.tsep.2023.101777
  38. Xia, et al., Numerical Study on the Enhanced Thermal Performance of the Porous Media-Assisted Flat-Plate Solar Collector, Int. J. Energy Res., 2023 (2023) 2244771. https://doi.org/10.1155/2023/2244771
  39. A. Handbook, and G. Atlanta, UAS: American Society of Heating, Refrigerating and Air Conditioning Engineers, 2003.
  40. V. Calmidi, and R.L. Mahajan, Forced convection in high porosity metal foams. J. Heat Transfer, 122 (2000) 557-565. https://doi.org/10.1115/1.1287793
  41. Alazmi, and K. Vafai, Constant wall heat flux boundary conditions in porous media under local thermal non-equilibrium conditions, Int. J. Heat Mass Transfer, 45 (2002) 3071-3087. https://doi.org/10.1016/S0017-9310(02)00044-3
  42. Liu, G. Xie, and T.W. Simon, Turbulent flow and heat transfer enhancement in rectangular channels with novel cylindrical grooves, Int. J. Heat Mass Transfer, 81 (2015) 563-577. https://doi.org/10.1016/j.ijheatmasstransfer.2014.10.021
  43. M. Patel, S.V. Jain, and V.J. Lakhera, Thermo-hydraulic performance analysis of a solar air heater roughened with reverse NACA profile ribs, Appl. Therm. Eng., 170 (2020) 114940. https://doi.org/10.1016/j.applthermaleng.2020.114940
  44. Webb, and E. Eckert, Application of rough surfaces to heat exchanger design, Int. J. Heat Mass Transfer, 15 (1972) 1647-1658. https://doi.org/10.1016/0017-9310(72)90095-6
  45. H. Jadhav, and N. Gnanasekaran, Optimum design of heat exchanging device for efficient heat absorption using high porosity metal foams, Int. Commun. Heat Mass Transfer, 126 (2021) 105475. https://doi.org/10.1016/j.icheatmasstransfer.2021.105475
  46. M. K. Ali, and S.L. Ghashim, Numerical analysis of the heat transfer enhancement by using metal foam, Case Stud. Therm. Eng., 49 (2023) 103336. https://doi.org/10.1016/j.csite.2023.103336
  47. Kotresha, and N. Gnanasekaran, Numerical simulations of fluid flow and heat transfer through aluminum and copper metal foam heat exchanger–a comparative study, Heat Transfer Eng., 41 (2019) 637-649. https://doi.org/10.1080/01457632.2018.1546969
  48. Lin, et al., Comparison and analysis of heat transfer in aluminum foam using local thermal equilibrium or non-equilibrium model, Heat Transfer Eng., 37 (2016) 314-322. https://doi.org/10.1080/01457632.2015.1052682
  49. V. Calmidi, Transport phenomena in high porosity fibrous metal foams. 1998: University of Colorado at Boulder.
  50. Lu, C. Zhao, and S. Tassou, Thermal analysis on metal-foam filled heat exchangers. Part I: Metal-foam filled pipes, Int. J. Heat Mass Transfer, 49 (2006) 2751-2761. https://doi.org/10.1016/j.ijheatmasstransfer.2005.12.012
  51. Boomsma, and D. Poulikakos, On the effective thermal conductivity of a three-dimensionally structured fluid-saturated metal foam, Int. J. Heat Mass Transfer, 44 (2001) 827-836. https://doi.org/10.1016/S0017-9310(00)00123-X
  52. Dukhan, Ö. Bağcı, and M. Özdemir, Thermal development in open-cell metal foam: An experiment with constant wall heat flux, Int. J. Heat Mass Transfer, 85 (2015) 852-859. https://doi.org/10.1016/j.ijheatmasstransfer.2015.02.047
  53. E. Nimvari, N.F. Jouybari, and Q. Esmaili, A new approach to mitigate intense temperature gradients in ceramic foam solar receivers, Renewable Energy, 122 (2018) 206-215. https://doi.org/10.1016/j.renene.2018.01.117
  54. Kurtbas, and N. Celik, Experimental investigation of forced and mixed convection heat transfer in a foam-filled horizontal rectangular channel, Int. J. Heat Mass Transfer, 52 (2009) 1313-1325. https://doi.org/10.1016/j.ijheatmasstransfer.2008.07.050
  55. Dukhan, M.A. Al-Rammahi, and A.S. Suleiman, Fluid temperature measurements inside metal foam and comparison to Brinkman–Darcy flow convection analysis, Int. J. Heat Mass Transfer, 67 (2013) 877-884. https://doi.org/10.1016/j.ijheatmasstransfer.2013.08.055
  56. P. Breugem, and B.-J. Boersma, Direct numerical simulations of turbulent flow over a permeable wall using a direct and a continuum approach, Phys. fluids, 17 (2005). https://doi.org/10.1063/1.1835771
  57. Chandesris, et al., Direct numerical simulation of turbulent heat transfer in a fluid-porous domain, Phys. Fluids, 25 (2013) 125110. https://doi.org/10.1063/1.4851416
  58. Qu, H. Xu, and W. Tao, Fully developed forced convective heat transfer in an annulus partially filled with metallic foams: an analytical solution, Int. J. Heat Mass Transfer, 55 (2012) 7508-7519. https://doi.org/10.1016/j.ijheatmasstransfer.2012.07.048
  59. Lu, T. Zhang, and M. Yang, Analytical solution of forced convective heat transfer in parallel-plate channel partially filled with metallic foams, Int. J. Heat Mass Transfer, 100 (2016) 718-727. https://doi.org/10.1016/j.ijheatmasstransfer.2016.04.047
  60. E. Nimvari, M. Maerefat, and M. El-Hossaini, Numerical simulation of turbulent flow and heat transfer in a channel partially filled with a porous media, Int. J. Therm. Sci., 60 (2012) 131-141. https://doi.org/10.1016/j.ijthermalsci.2012.05.016
  61. Sethi, and N. Thakur, Correlations for solar air heater duct with dimpled shape roughness elements on absorber plate, Sol. Energy, 86 (2012) 2852-2861. https://doi.org/10.1016/j.solener.2012.06.024
Statistics
Article View: 318
PDF Download: 378


Journal Management System. Powered by iJournalPro.com