Experimental Investigation of Artificial Cavities Effect of Single-Phase Fluid Flow and Heat Transfer in Single Microchannel

Al-Nakeeb, Qahtan A.; Fayyadh, Ekhlas M.; Hasan, Moayed R.

doi:10.30684/etj.v40i1.2122

	Experimental Investigation of Artificial Cavities Effect of Single-Phase Fluid Flow and Heat Transfer in Single Microchannel
Engineering and Technology Journal
Article 13, Volume 40, Issue 1, 2022, Pages 109-119 PDF (1.02 M)
DOI: 10.30684/etj.v40i1.2122
Authors
Qahtan A. Al-Nakeeb^* ; Ekhlas M. Fayyadh; Moayed R. Hasan
Department of Mechanical Engineering, University of Technology-Iraq, Alsina’a street, 10066 Baghdad, Iraq.
Abstract
In this paper, an experimental study has been conducted to investigate the influence of artificial cavities (artificial nucleation sites, ANS) in a single microchannel on the characteristics of flow and heat transfer at a single-phase flow. The experiments were performed with deionized water as a working fluid at 30OC inlet temperature with a range (108.6-2372) of Reynolds numbers. Three models of the straight microchannel (model-1, model-2, and model-3) were manufactured of brass having a rectangular shape with a hydraulic diameter of (0.42 mm). Model-1 has a smooth surface, while model-2 has artificial cavities with a number of 40 ANS located on the base of the microchannel; along a line adjacent to one of the sidewalls. Also, the artificial cavities of model-3 exist at the base of the microchannel; along a line that is nearest to each sidewall for the microchannel. The number of ANS at each sidewall is 40 (i.e. the overall number of artificial nucleations is 80). The results manifested the enhancement of heat transfer by the presence of ANS for model-2 and model-3 as compared to model-1 by 15.53% and 16.67%, respectively. Also, the results proved that the fanning friction factor correlation for laminar and turbulent flow can predict very well the results (MAE=6.6-7.2%) and (MAE=4.1-7.7%), respectively. Also, the Nusselt number increases with increasing Reynolds number. However, the conventional correlation that predicted the experimental results is lower than the correlations (MAE=30.1%, 13.2% and 12.6%) for Model-1, -2 and -3, respectively.
Highlights
The traditional (conventional) correlation is appropriate for predicting the friction factor for smooth surface of microchannel. as well as microchannel which uses artificial nucleation sites. Developing heat transfer flow region is a dominated heat transfer in microchannel within experimental work operation conditions. Enhancement of the heat transfer performance for the microchannel by using artificial nucleation sites as compared to the smooth surface of microchannel.
Keywords
Microchannel; Single-phase flow; Friction factor; Nusselt number; Pressure drop

References
[1] I. Mudawar, “Recent advances in high-flux, two-phase thermal management,” J. Therm. Sci. Eng. Appl., 5 (2013) 1-15. [2] T. M. Harms, M. J. Kazmierczak, and F. M. Gerner, “Developing convective heat transfer in deep rectangular microchannels,” Int. J. Heat Fluid Flow, 20 (1999) 149–157. [3] W. Qu and I. Mudawar, “Experimental and numerical study of pressure drop and heat transfer in a single-phase micro-channel heat sink,” Int. J. Heat Mass Transf., 45 (2002) 2549–2565. [4] P. S. Lee, S. V Garimella, and D. Liu, “Investigation of heat transfer in rectangular microchannels,” Int. J. Heat Mass Transf., 48 (2005) 1688–1704. [5] J. Y. Jung and H.Y. Kwak, “Fluid flow and heat transfer in microchannels with rectangular cross section,” Heat Mass Transf., 44 (2008) 1041–1049. [6] N. García-Hernando, A. Acosta-Iborra, U. Ruiz-Rivas, and M. Izquierdo, “Experimental investigation of fluid flow and heat transfer in a single-phase liquid flow micro-heat exchanger,” Int. J. Heat Mass Transf., 52 (2009) 5433–5446. [7] M. Mirmanto, D. B. R. Kenning, J. S. Lewis, and T. G. Karayiannis, “Pressure drop and heat transfer characteristics for single-phase developing flow of water in rectangular microchannels,” J. Phys. Conf. Ser., 395 (2012) 13. [8] T. Y. Lin and S. G. Kandlikar, “An experimental investigation of structured roughness effect on heat transfer during single-phase liquid flow at microscale,” J. Heat Transfer, 134 (2012) 1–9. [9] M. M. Salem, M. H. Elhsnawi, and S. B. Mohamed, “Experimental Investigation of Surface Roughness Effect on Single Phase Fluid Flow and Heat Transfer in Micro-Tube,” Int. J. Mech. Mechatronics Eng., 7 (2013) 1821–1825. [10] A. Tamayol, J. Yeom, M. Akbari, and M. Bahrami, “Low Reynolds number flows across ordered arrays of micro-cylinders embedded in a rectangular micro/minichannel,” Int. J. Heat Mass Transf., 58 (2013) 420–426. [11] Y. Xing, Z. Tao, H. Li, and Y. Tian, “Experimental investigation of surface roughness effects on flow behavior and heat transfer characteristics for circular microchannels,” Chinese J. Aeronaut., 29 (2016) 1575–1581. [12] B. Markal, O. Aydin, and M. Avci, “Experimental study of single-phase fluid flow and heat transfer characteristics in rectangular microchannels,” Isi Bilim. Ve Tek. Dergisi/ J. Therm. Sci. Technol., 38 (2018) 65–72. [13] R. Kumar, M. Islam, and M. M. Hasan, “Investigations on Single-Phase Liquid Flow through Semi-Circular Microchannels,” Int. J. Appl. Eng. Res., 13 (2018) 6870–6880. [14] B. Huang, H. Li, S. Xia, and T. Xu, “Experimental investigation of the flow and heat transfer performance in micro-channel heat exchangers with cavities,” Int. J. Heat Mass Transf., 159 (2020) 1-10. [15] S. A. Mohammed and E. M. Fayyadh, “Effect of artificial cavities on heat transfer and flow characteristics microchannel,” IRAQI J. Mech. Mater. Eng., 20 (2020) 180–192. [16] M. R. Özdemir, M. M. Mahmoud, and T. G. Karayiannis, “Flow Boiling of Water in a Rectangular Metallic Microchannel,” Heat Transf. Eng.,(2020) 1–25. [17] S. G. Kandlikar, S. Garimella, D. Li, S. Colin, and M. R. King, Heat Transfer and Fluid Flow in Minichannels and Microchannels, 2nd Editio. Elsevier, 2014. [18] E. J. Shaughnessy Jr., I. M. Katz, and J. P. Schaffer, Introduction to Fluid Mechanics., Oxford universiry press, NY, USA, 2005. [19] R. K. Shah and A. L. London, Laminar Flow Forced Convection in Ducts. Elsevier,Oxford Acadamic Press, NY, USA, suppliment 1 to advance in heat transfer, 1978. [20] A. Koşar, C.-J. Kuo, and Y. Peles, “Boiling heat transfer in rectangular microchannels with reentrant cavities,” Int. J. Heat Mass Transf., 48 (2005) 4867–4886. [21] H. W. Coleman and W. G. Steele, Experimentation, Validation, And Uncertainty Analysis For Engineers, Fourth edi. 2018. [22] R. J. Phillips, “Forced-convection, liquid-cooled, microchannel heat sinks,” MSc thesis, Massachusetts Institute of Technolog, Cambridge, USA, 1987. [23] M. Mirmanto, “Single-phase flow and flow boiling of water in horizontal rectangular microchannels,” PhD thesis, Brunel University, London, UK, 2013. [24] M. R. Özdemir, “Single – Phase Flow and Flow Boiling of Water in Rectangular Metallic Microchannels,” PhD thesis, Brunel University, London, UK, 2016.
Statistics Article View: 438 PDF Download: 439